Nissan Juke Service and Repair Manual : Engine Control System MR16DDT
- Precaution
- Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
- Precaution for Procedure without Cowl Top Cover
- On Board Diagnostic (OBD) System of Engine and CVT
- General Precauti
- Preparation
- System description
- System
- Engine control system
- Direct injection gasoline system
- Fuel pressure control
- Electric ignition system
- Intake valve timing control
- Exhaust valve timing control
- Turbocharger boost control
- Engine protection control at low engine oil pressure
- Air conditioning cut control
- Cooling fan control
- Starter motor drive control
- Evaporative emission system
- Automatic speed control device (ASCD)
- Speed limiter
- NISSAN dynamic control system
- Can communication
- Operation
- Speed limiter
- On board diagnostic (OBD) system
- Diagnosis system (ECM)
- Ecu diagnosis information
- Wiring diagram
- Basic inspection
- Diagnosis and repair workflow
- Basic inspection
- Additional service when replacing ECM
- Accelerator pedal released position learning
- Throttle valve closed position learning
- Idle air volume learning
- G sensor calibration
- Mixture ratio self-learning value clear
- Fuel pressure
- How to set srt code
- DTC/Circuit diagnosis
- Trouble diagnosis - specification value
- Power supply and ground circuit
- U0101 Can comm circuit
- U0122 Vehicle dynamics control module
- U1001 Can comm circuit
- P0011 IVT control
- P0014 EVT control
- P0031, P0032 A/F sensor 1 heater
- P0037, P0038 HO2S2 heater
- P0045, P0047, P0048 TC boost control solenoid valve
- P0075 IVT control solenoid valve
- P0078 EVT control solenoid valve
- P0087, P0088, P0090 FRP control system
- P0097, P0098 IAT sensor 2
- P0102, P0103 MAF sensor
- P0107, P0108 atmospheric pressure sensor
- P0112, P0113 IAT sensor
- P0117, P0118 ECT sensor
- P0122, P0123 TP sensor
- P0130 A/F sensor 1
- P0131 A/F sensor 1
- P0132 A/F sensor 1
- P0133 A/F sensor 1
- P0137 HO2S2
- P0138 HO2S2
- P0139 HO2S2
- P0171 fuel injection system function
- P0172 fuel injection system function
- P0190 FRP sensor
- P0197, P0198 EOT sensor
- P0201, P0202, P0203, P0204 fuel injector
- P0222, P0223 TP sensor
- P0234 TC system
- P0237, P0238 TC boost sensor
- P0300, P0301, P0302, P0303, P0304 misfire
- P0327, P0328 KS
- P0335 CKP sensor (POS)
- P0340 CMP sensor (PHASE)
- P0420 three way catalyst function
- P0444 EVAP canister purge volume control solenoid valve
- P0500 VSS
- P0501, P2159 vehicle speed sensor
- P0506 ISC system
- P0507 ISC system
- P0520 EOP sensor
- P0524 engine oil pressure
- P0603 ECM power supply
- P0605 ECM
- P0607 ECM
- P0611 ECM protection
- P062B ECM
- P0643 sensor power supply
- P0850 PNP switch
- P1078 EVT control position sensor
- P1197 out of gas
- P1212 TCS communication line
- P1217 engine over temperature
- P1220 fuel pump control module (FPCM)
- P1225 TP sensor
- P1226 TP sensor
- P1550 battery current sensor
- P1551, P1552 battery current sensor
- P1553 battery current sensor
- P1554 battery current sensor
- P1556, P1557 battery temperature sensor
- P1564 ASCD steering switch
- P1572 ASCD brake switch
- P1574 ASCD vehicle speed sensor
- P158A ECM
- P159A, P159C, P159D G sensor
- Except for M/T models
- P159B G sensor
- P1650 starter motor relay 2
- P1651 starter motor relay
- P1652 starter motor system COMM
- P1805 brake switch
- P2100, P2103 throttle control motor relay
- P2101 electric throttle control function
- P2118 throttle control motor
- P2119 electric throttle control actuator
- P2122, P2123 APP sensor
- P2127, P2128 APP sensor
- P2135 TP sensor
- P2138 APP sensor
- P2162 vehicle speed sensor
- Fuel injector
- Low pressure fuel pump
- High pressure fuel pump
- Ignition signal
- Electrical load signal
- Cooling fan
- Refrigerant pressure sensor
- Brake pedal position switch
- Clutch pedal position switch
- ASCD main switch
- SPEED LIMITER MAIN SWITCH
- Information display (ASCD)
- Information display (speed limiter)
- Malfunction indicator lamp
- Symptom diagnosis
- Periodic maintenance
- Removal and installation
- Service data and specifications (SDS)
Thermostat
...
Precaution
...
Other materials:
Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
NOTE:
• Before removing and installing any control units, first turn the ignition
switch to the LOCK position, then disconnect
both battery cables.
• After finishing work, confirm that all control unit connectors are connected
properly, then re-connect both
battery cables.
• Always us ...
Service Notice
• When removing or installing various parts, place a cloth or padding onto
the vehicle body to prevent
scratches.
• Handle trim, molding, instruments, grille, etc. carefully during removing or
installing. Be careful not to oil or
damage them.
• Apply sealing compound where necessary wh ...
Engine control system
Symptom Table
SYSTEM — BASIC ENGINE CONTROL SYSTEM
1 - 6: The numbers refer to the order of inspection.
(continued on next page)
SYSTEM — ENGINE MECHANICAL & OTHER
1 - 6: The numbers refer to the order of inspection. ...
