Nissan Juke Service and Repair Manual : DTC/Circuit diagnosis
- Trouble diagnosis - specification value
- Power supply and ground circuit
- U0101 Can comm circuit
- U0122 Vehicle dynamics control module
- U1001 Can comm circuit
- P0011 IVT control
- P0014 EVT control
- P0031, P0032 A/F sensor 1 heater
- P0037, P0038 HO2S2 heater
- P0045, P0047, P0048 TC boost control solenoid valve
- P0075 IVT control solenoid valve
- P0078 EVT control solenoid valve
- P0087, P0088, P0090 FRP control system
- P0097, P0098 IAT sensor 2
- P0102, P0103 MAF sensor
- P0107, P0108 atmospheric pressure sensor
- P0112, P0113 IAT sensor
- P0117, P0118 ECT sensor
- P0122, P0123 TP sensor
- P0130 A/F sensor 1
- P0131 A/F sensor 1
- P0132 A/F sensor 1
- P0133 A/F sensor 1
- P0137 HO2S2
- P0138 HO2S2
- P0139 HO2S2
- P0171 fuel injection system function
- P0172 fuel injection system function
- P0190 FRP sensor
- P0197, P0198 EOT sensor
- P0201, P0202, P0203, P0204 fuel injector
- P0222, P0223 TP sensor
- P0234 TC system
- P0237, P0238 TC boost sensor
- P0300, P0301, P0302, P0303, P0304 misfire
- P0327, P0328 KS
- P0335 CKP sensor (POS)
- P0340 CMP sensor (PHASE)
- P0420 three way catalyst function
- P0444 EVAP canister purge volume control solenoid valve
- P0500 VSS
- P0501, P2159 vehicle speed sensor
- P0506 ISC system
- P0507 ISC system
- P0520 EOP sensor
- P0524 engine oil pressure
- P0603 ECM power supply
- P0605 ECM
- P0607 ECM
- P0611 ECM protection
- P062B ECM
- P0643 sensor power supply
- P0850 PNP switch
- P1078 EVT control position sensor
- P1197 out of gas
- P1212 TCS communication line
- P1217 engine over temperature
- P1220 fuel pump control module (FPCM)
- P1225 TP sensor
- P1226 TP sensor
- P1550 battery current sensor
- P1551, P1552 battery current sensor
- P1553 battery current sensor
- P1554 battery current sensor
- P1556, P1557 battery temperature sensor
- P1564 ASCD steering switch
- P1572 ASCD brake switch
- P1574 ASCD vehicle speed sensor
- P158A ECM
- P159A, P159C, P159D G sensor
- Except for M/T models
- P159B G sensor
- P1650 starter motor relay 2
- P1651 starter motor relay
- P1652 starter motor system COMM
- P1805 brake switch
- P2100, P2103 throttle control motor relay
- P2101 electric throttle control function
- P2118 throttle control motor
- P2119 electric throttle control actuator
- P2122, P2123 APP sensor
- P2127, P2128 APP sensor
- P2135 TP sensor
- P2138 APP sensor
- P2162 vehicle speed sensor
- Fuel injector
- Low pressure fuel pump
- High pressure fuel pump
- Ignition signal
- Electrical load signal
- Cooling fan
- Refrigerant pressure sensor
- Brake pedal position switch
- Clutch pedal position switch
- ASCD main switch
- SPEED LIMITER MAIN SWITCH
- Information display (ASCD)
- Information display (speed limiter)
- Malfunction indicator lamp
How to set srt code
Description
OUTLINE
In order to set all SRTs, the self-diagnoses as in the “SRT ITEM” table must
have been performed at least
once. Each diagnosis may require actual driving for a long period of ...
Trouble diagnosis - specification
value
Description
The specification (SP) value indicates the tolerance of the value that is
displayed in “SPEC” of “DATA MONITOR”
mode of CONSULT-III during normal operation of the Engine Control Syste ...
Other materials:
P062B ECM
Description
This DTC is detected when the ECM-integrated injector driver unit has a
malfunction. For injector driver unit,
refer to EC-31, "ECM".
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at least 10 seconds.
...
System
Relay control system
RELAY CONTROL SYSTEM : System Diagram
*1: Except for MR16DDT engine models
*2: For MR16DDT engine models
RELAY CONTROL SYSTEM : System Description
IPDM E/R activates the internal control circuit to perform the relay ON-OFF
control according to the input signals
from va ...
B1170, B1171, B1172, B1173, B1174, B1175 diagnosis sensor uniT
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT
With CONSULT-III
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.
Without CONSULT-III
1. Turn ignition switch ON.
2. Check the air bag warning lamp statu ...
