Nissan Juke Service and Repair Manual : P1652 starter motor system COMM

Description

ECM controls ON/OFF state of the starter relay, according to the engine and vehicle condition. Models with no Intelligent Key System transmit a control signal directly to IPDM E/R. On the other hand, models with the Intelligent Key System transmit a control signal to IPDM E/R by way of BCM via CAN communication.

Under normal conditions, ECM controls and maintains the starter relay in OFF state during engine running or “D” position.

When detecting a decrease in engine speed due to rapid deceleration or heavy load condition, ECM controls and reactivates the starter relay.

IPDM E/R detects a control state of starter relay and starter control relay and transmits a feedback signal to ECM via CAN communication.

DTC Logic

DTC DETECTION LOGIC

NOTE

:
• If DTC P1650 is displayed with DTC U1001, perform the trouble diagnosis for DTC U1001. Refer to EC-161, "DTC Logic".

• If DTC P1650 is displayed with DTC P0607, perform the trouble diagnosis for DTC P0607. Refer to EC-304, "DTC Logic".

• If DTC P1650 is displayed with B209F or B20A0 of IPDM E/R, perform the trouble diagnosis for B209F or B20A0. Refer to SEC-134, "DTC Logic" or SEC-136, "DTC Logic".

• If DTC P1650 is displayed with B26F9 or B26FA of BCM, perform the trouble diagnosis for B209F or B20A0.

Refer to SEC-128, "DTC Logic" or SEC-130, "DTC Logic".

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON and wait at least 5 minutes.

3. Check DTC.

Is DTC detected? YES >> Proceed to EC-372, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.INSPECTION START

1. Erase DTC.

2. Perform DTC confirmation procedure. Refer to EC-372, "DTC Logic".

3. Check DTC.

Is the P1652 displayed again?

YES >> GO TO 2.

NO >> INSPECTION END

2.CHECK INTERMITTENT INCIDENT

Perform GI-42, "Intermittent Incident".

Is the inspection result normal? YES >> Replace IPDM E/R. Refer to PCS-34, "Removal and Installation".

NG >> Repair or replace error-detected parts.

    5. Also check harness for short to ground to power. Is the inspection result normal? YES >> GO TO 7. NO >> Repair or replace error-detected parts. 7.CHECK INTERMITTENT INCIDENT ...

    P1805 brake switch
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE 1. Turn ignition switch ON. 2. Fully depress the brake pedal for at least 5 seconds. 3. Erase the ...

    Other materials:

    NISSAN Vehicle Immobilizer System keys
    You can only drive your vehicle using the authorized master keys which are officially registered to the advanced NISSAN Vehicle Immobilizer System components inside your vehicle. These high-security keys feature a specialized electronic transponder chip molded directly into the key head, which commu ...

    Diagnosis system (IPDM E/R)
    Diagnosis Description AUTO ACTIVE TEST Description In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation. • Oil pressure warning lamp (only for K9K engine models) • Rear window defogger • Front wiper motor • Parking lamp • ...

    RearView Monitor
    CAMERA button (used to manually trigger the display views or adjust active screen brightness layouts) MENU button (opens up global display preferences and system option configuration screens) WARNING Failure to follow all safety warnings and t ...