Nissan Juke Service and Repair Manual : P2119 electric throttle control actuator

DTC Logic

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A AND B

1. Turn ignition switch ON and wait at least 1 second.

2. Set selector lever to D (CVT) or 1st (M/T) position and wait at least 3 seconds.

3. Set selector lever to P (CVT) or Neutral (M/T) position.

4. Turn ignition switch OFF and wait at least 10 seconds.

5. Turn ignition switch ON and wait at least 1 second.

6. Set selector lever to D (CVT) or 1st (M/T) position and wait at least 3 seconds.

7. Set selector lever to P (CVT) or Neutral (M/T) position.

8. Turn ignition switch OFF, wait at least 10 seconds and then turn ON.

9. Check DTC.

Is DTC detected? YES >> Proceed to EC-383, "Diagnosis Procedure".

NO >> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION C

1. Turn ignition switch ON and wait at least 1 second.

2. Set selector lever to D (CVT) or 1st (M/T) position and wait at least 3 seconds.

3. Set selector lever to P (CVT) or Neutral (M/T) position.

4. Start engine and let it idle for 3 seconds.

5. Check DTC.

Is DTC detected? YES >> Proceed to EC-383, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY

1. Remove the intake air duct. Refer to EM-26, "Exploded View".

2. Check if foreign matter is caught between the throttle valve and the housing.

Is the inspection result normal? YES >> Replace electric throttle control actuator. Refer to EM-28, "Exploded View".

NO >> Remove the foreign matter and clean the electric throttle control actuator inside, then perform throttle valve closed position learning. Refer to EC-135, "Work Procedure".

    P2118 throttle control motor
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conductin ...

    P2122, P2123 APP sensor
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC P2122 or P2123 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to EC-307, "DTC Logic". DTC CONFIRM ...

    Other materials:

    HR16DE : Removal and Installation
    REMOVAL 1. Disconnect the battery cable from the negative terminal. Refer to PG-124, "Removal and Installation". 2. Remove radiator reservoir tank. Refer to CO-17, "Exploded View". 3. Disconnect harness connectors (1) from battery terminal with fusible link. 4. Remove harn ...

    Rear window defogger relay
    Description The rear window defogger is operated by turning the rear window defogger switch ON. Component Function Check 1.CHECK FUNCTION 1. Perform IPDM E/R Active Test (“REAR DEFOGGER”) using CONSULT-III. 2. Touch “ON”. 3. Check that the rear window heating wire is getting warmer. ...

    P0488 EGR system
    DTC Logic DTC DETECTION LOGIC Diagnosis Procedure 1.CHECK EGR VOLUME CONTROL VALVE CONTROL CIRCUIT 1. Turn ignition switch OFF. 2. Disconnect EGR volume control valve harness connector and ECM harness connector. 3. Check the continuity between EGR volume control valve terminal harness co ...