Nissan Juke Service and Repair Manual : DTC/circuit diagnosis
- Power supply and ground circuit
- P0001 fuel pump
- P0002 fuel pump
- P0016 CKP - CMP correlation
- P0045 TC boost control solenoid valve
- P0087 fuel pump
- P0089 fuel pump
- P0090 fuel pump
- P0100 MAF sensor
- P0101 MAF sensor
- P0110 IAT sensor
- P0115 ECT sensor
- P0120 TP sensor
- P012A TC boost sensor
- P012B TC boost sensor
- P0180 FPT sensor
- P0190 FRP sensor
- P0200 fuel injector
- P0201, P0202, P0203, P0204 fuel injector
- P0217 engine over temperature
- P0225 APP sensor
- P0226 APP sensor
- P0263, P0266, P0269, P0272 fuel injector
- P0335 CKP sensor (POS)
- P0340 CMP sensor (phase)
- P0380 glow rela
- P0402 EGR volume control valve
- P0403 EGR volume control valve
- P0409 EGR volume control valve control position sensor
- P0470 exhaust gas pressure sensor 1
- P0471 exhaust gas pressure sensor 1
- P047A exhaust gas pressure sensor 2
- P047B exhaust gas pressure sensor 2
- P0487 EGR volume control valve
- P0488 EGR system
- P0504 ASCD brake SWI
- P0525 ASCD system
- P0530 refrigerant pressure sensor
- P0544 EGT sensor 1
- P0560 battery voltage
- P0564 ASCD steering switch
- P0574 VSS
- P0575 ASCD steering switch
- P0606 ECM
- P060A ECM
- P060B ECM
- P061A ECM
- P062B ECM
- P0638 electric throttle control actuator function
- P0641 sensor power supply
- P0651 sensor power supply
- P0657 ECM relay
- P0697 sensor power supply
- P0833 CPP switch
- P1205 exhaust fuel injector
- P1525 communication circuit for ASCD and speed limiter
- P1544 EGT sensor 2
- P1545 EGT sensor 2
- P160C ECM
- P1632 fuel cut off valve
- P1641 thermoplunger control unit
- P1642 thermoplunger control unit
- P1643 thermoplunger control unit
- P1650 thermoplunger control unit
- P2002 diesel particulate filter
- P2080 EGT sensor 1
- P2100 electric throttle control function
- P2119 electric throttle control function
- P2120 APP sensor
- P2226 baro sensor
- P2263 TC system
- P245A EGR cooler bypass valve control solenoid valve
- PC415 communication circuit
- ASCD main switch
- ASCD steering switch
- CAN communication circuit
- Cooling fan
- Information display (ASCD)
- Information display (speed limiter))
- Malfunction indicator
- Speed limiter main switch
DPF (diesel particulate filter) data clear
Description
Perform ???DIESEL PARTICULATE FILTER DATA CLEAR??? in ???WORK SUPPORT??? mode with
CONSULT-III
when oxidation catalyst with diesel particulate filter is replaced as new one.
Based on ...
Power supply and ground circuit
Diagnosis Procedure
1.INSPECTION START
Start engine.
Is engine running?
YES >> GO TO 6.
NO >> GO TO 2.
2.CHECK GROUND CONNECTION-I
1. Turn ignition switch OFF.
2. Check groun ...
Other materials:
P0335 CKP sensor (POS)
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn
ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following proced ...
Magnet clutch
Component Function Check
1.CHECK MAGNET CLUTCH OPERATION
Perform auto active test of IPDM E/R. Refer to PCS-12, "Diagnosis
Description" (with Intelligent Key) or PCS-
43, "Diagnosis Description" (without Intelligent Key).
Does it operate normally?
YES >> INSPECTION ...
HR16DE : Inspection and Adjust
INSPECTION
Magnetic Switch Check
• Before starting to check, disconnect the battery cable from the negative
terminal.
• Disconnect “M” terminal of starter motor.
1. Continuity test [between “S” terminal (A) and switch body]
B : “B” terminal
C : “M” terminal
• Replace magnetic switch if co ...
