Nissan Juke Service and Repair Manual : P0101 MAF sensor
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK AIR FILTER
Check that air filter is not obstructed.
Is the inspection result normal? Yes >> Repair or replace.
No >> GO TO 2.
2.CHECK INTAKE AIR DUCT
Check that intake air duct is not obstructed.
Is the inspection result normal? Yes >> Repair or replace.
No >> GO TO 3.
3.CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF.
2. Check ground connection E38. Refer to Ground inspection in GI-44, "Circuit Inspection".
Is the inspection result normal? YES >> GO TO 4.
NO >> Repair or replace ground connection.
4.CHECK MASS AIR FLOW SENSOR POWER SUPPLY CIRCUIT-I
1. Turn ignition switch OFF.
2. Disconnect mass air flow sensor harness connector.
3. Turn ignition switch ON.
4. Check the voltage between mass air flow sensor harness connector and ground.
Is the inspection result normal? YES >> GO TO 6.
NO >> GO TO 5.
5.DETECT MALFANCTIONING PART
Check the following.
• Harness connectors E8, F1 • Harness for open or short between IPDM E/R and mass air flow sensor
>> Repair open circuit or short to ground or short to power in harness or connectors.
6.CHECK MASS AIR FLOW SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between mass air flow sensor harness connector and ECM harness connector.
4. Also check harness for short to ground and short to power.
Is the inspection result normal? YES >> GO TO 7.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
7.CHECK MASS AIR FLOW SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Check the continuity between mass air flow sensor harness connector and ECM harness connector.
2. Also check harness for short to ground and short to power.
Is the inspection result normal? YES >> GO TO 8.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
8.CHECK MASS AIR FLOW SENSOR
Refer to EC-904, "Component Inspection" Is the inspection result normal? YES >> GO TO 9.
NO >> Replace mass air flow sensor.
9.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "Intermittent Incident", ???INCIDENT SIMULATION TESTS??? and ???GROUND INSPECTION???.
>> INSPECTION END
Component Inspection
1.CHECK MASS AIR FLOW SENSOR
1. Turn ignition switch OFF.
2. Reconnect all harness connectors disconnected.
3. Turn ignition switch ON.
4. Check the voltage between mass air flow sensor harness connector.
Is the inspection result normal? YES >> INSPECTION END
NO >> Replace mass air flow sensor.
P0100 MAF sensor
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF.
2. Check ground connection E38. Refer to Ground inspection in GI-44, "Circuit
In ...
P0110 IAT sensor
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF.
2. Check ground connection E38. Refer to Ground inspection in GI-44, "Circuit
In ...
Other materials:
Control buttons
The control buttons for the Bluetooth® Hands- Free Phone System are located on
the steering wheel.
PHONE SEND
Push the button to initiate a VR
session or answer an incoming call.
You can also use the button to
interrupt system feedback and give a command at once.
PHONE END
While th ...
Types of tires
WARNING
• When changing or replacing tires, be sure all four tires are of the same
type (Example: Summer, All Season or Snow) and construction. A NISSAN dealer may
be able to help you with information about tire type, size, speed rating and availability.
• Replacement tires may have a lowe ...
Position switch
Removal and Installation
REMOVAL
1. Remove air cleaner case. (K9K) Refer to EM-280, "Removal and
Installation".
2. Remove battery. (MR16DDT) Refer to PG-124, "Removal and Installation".
3. Disconnect position switch connector.
4. Remove position switch from transaxle case. ...
