Nissan Juke Service and Repair Manual : P0471 exhaust gas pressure sensor 1

DTC Logic

DTC DETECTION LOGIC

NOTE:


NOTE

:
If DTC P0471 is displayed with DTC P0470 or P2226, first perform trouble diagnosis for DTC P0470 or P2226.

Refer to EC-944, "DTC Logic" (P0470), EC-1002, "DTC Logic" (P2226).

Diagnosis Procedure

1.CHECK GROUND CONNECTIONS

1. Turn ignition switch OFF and wait at least 20 seconds.

2. Check ground connection E38. Refer to Ground inspection in GI-44, "Circuit Inspection".

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace ground connection.

2.CHECK EXHAUST GAS PRESSURE SENSOR 1 AND EXHAUST GAS PIPE INSTALLATION

Check exhaust gas pressure sensor and exhaust gas pipe for poor installation and damage.

Is the inspection result normal? YES >> GO TO 3.

NO >> Install exhaust gas pressure sensor and exhaust gas pipe properly.

3.CHECK EXHAUST GAS PRESSURE SENSOR 1 POWER SUPPLY CIRCUIT

1. Disconnect exhaust pressure sensor 1 harness connector.

2. Turn ignition switch ON.

3. Check the voltage between exhaust gas pressure sensor 1 harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

4.CHECK EXHAUST GAS PRESSURE SENSOR 1 GROUND CIRCUIT FOR OPEN AND SHORT

1. Turn ignition switch OFF and wait at least 20 seconds.

2. Check the continuity between exhaust gas pressure sensor 1 harness connector and ECM harness connector.

3. Also check harness for short to ground and short to power.


3. Also check harness for short to ground and short to power.

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

5.CHECK EXHAUST PRESSURE SENSOR 1 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1. Check the continuity between exhaust gas pressure sensor 1 harness connector and ECM harness connector.

2. Also check harness for short to ground and short to power.


2. Also check harness for short to ground and short to power.

Is the inspection result normal? YES >> GO TO 6.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

6.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident".

Is the inspection result normal? YES >> Replace exhaust gas pressure sensor 1.

NO >> Repair or replace.

    P0470 exhaust gas pressure sensor 1
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0470 is displayed with DTC P0651 or P2263, first perform trouble diagnosis for DTC P0651 or P2263. Refer to EC-975, "DTC Logic" (P0651), ...

    P047A exhaust gas pressure sensor 2
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC P047A is displayed with DTC P0651, first perform trouble diagnosis for DTC P0651. Refer to EC-975, "DTC Logic". Diagnosis Procedure 1.CHE ...

    Other materials:

    Service data and specifications (SDS)
    Wheel Bearing Drive Shaft M/T *: For measuring position, refer to FAX-54, "WHEEL SIDE : Disassembly and Assembly" (Wheel side), FAX- 56, "TRANSAXLE SIDE : Disassembly and Assembly" (Transaxle side). CVT *: For measuring position, refer to FAX-54, "WHEEL SIDE ...

    Horn function
    Component Function Check 1.CHECK FUNCTION 1 1. Disconnect vehicle security horn relay. 2. Perform “VEHICLE SECURITY HORN” in “ACTIVE TEST” mode of “THEFT ALM” of “BCM” using CONSULT- III. 3. Check the horn operation. Is the operation normal? YES >> GO TO 2. NO > ...

    Basic inspection
    Work Procedure 1.INSPECTION START 1. Check service records for any recent repairs that may indicate a related malfunction, or a current need for scheduled maintenance. 2. Open engine hood and check the following: - Harness connectors for improper connections - Wiring harness for improper con ...