Nissan Juke Service and Repair Manual : P0470 exhaust gas pressure sensor 1

DTC Logic

DTC DETECTION LOGIC

NOTE:


NOTE

:
If DTC P0470 is displayed with DTC P0651 or P2263, first perform trouble diagnosis for DTC P0651 or P2263.

Refer to EC-975, "DTC Logic" (P0651), EC-1003, "DTC Logic" (P2263).

Diagnosis Procedure

1.CHECK GROUND CONNECTIONS

1. Turn ignition switch OFF and wait at least 20 seconds.

2. Check ground connection E38. Refer to Ground inspection in GI-44, "Circuit Inspection".

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace ground connection.

2.CHECK EXHAUST GAS PRESSURE SENSOR 1 POWER SUPPLY CIRCUIT

1. Disconnect exhaust gas pressure sensor 1 harness connector.

2. Turn ignition switch ON.

3. Check the voltage between exhaust pressure sensor 1 harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

3.CHECK EXHAUST GAS PRESSURE SENSOR 1 GROUND CIRCUIT FOR OPEN AND SHORT

1. Turn ignition switch OFF and wait at least 20 seconds.

2. Check the continuity between exhaust gas pressure sensor 1 harness connector and ECM harness connector.

3. Also check harness for short to ground and short to power.


3. Also check harness for short to ground and short to power.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

4.CHECK EXHAUST GAS PRESSURE SENSOR 1 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1. Check the continuity between exhaust gas pressure sensor 1 harness connector and ECM harness connector.

2. Also check harness for short to ground and short to power.


2. Also check harness for short to ground and short to power.

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

5.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident".

Is the inspection result normal? YES >> Replace exhaust gas pressure sensor 1.

NO >> Repair or replace.

    P0409 EGR volume control valve control position sensor
    DTC Logic DTC DETECTION LOGIC Diagnosis Procedure 1.CHECK GROUND CONNECTIONS 1. Turn ignition switch OFF. 2. Check ground connection E38. Refer to Ground inspection in GI-44, "Circuit In ...

    P0471 exhaust gas pressure sensor 1
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0471 is displayed with DTC P0470 or P2226, first perform trouble diagnosis for DTC P0470 or P2226. Refer to EC-944, "DTC Logic" (P0470), ...

    Other materials:

    How to set SRT code
    Description OUTLINE In order to set all SRTs, the self-diagnoses as in the “SRT ITEM” table must have been performed at least once. Each diagnosis may require actual driving for a long period of time under various conditions. SRT ITEM The table below shows required self-diagnostic ite ...

    Fuel filler lid opener
    Exploded View 1. Fuel filler lid opener cable 2. Cable protector 3. Fuel filler lid lock assembly 4. Fuel filler lid assembly 5. Spring 6. Bumper rubber : Clip : Do not reuse Fuel filler lid FUEL FILLER LID : Removal and Installation REMOVAL 1. Fully open fuel filler lid. 2. Remov ...

    Hazard switch
    Component Function Check 1.CHECK HAZARD SWITCH SIGNAL BY CONSULT-III CONSULT-III DATA MONITOR 1. Turn the ignition switch ON. 2. Select “HAZARD SW” of BCM (FLASHER) data monitor item. 3. With operating the hazard switch, check the monitor status. Is the inspection result normal? YES > ...