Nissan Juke Service and Repair Manual : P047A exhaust gas pressure sensor 2

DTC Logic

DTC DETECTION LOGIC

NOTE:


NOTE

:
If DTC P047A is displayed with DTC P0651, first perform trouble diagnosis for DTC P0651. Refer to EC-975, "DTC Logic".

Diagnosis Procedure

1.CHECK GROUND CONNECTIONS

1. Turn ignition switch OFF and wait at least 20 seconds.

2. Check ground connection E38. Refer to Ground inspection in GI-44, "Circuit Inspection".

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace ground connection.

2.CHECK EXHAUST GAS PRESSURE SENSOR 2 POWER SUPPLY CIRCUIT

1. Disconnect exhaust gas pressure sensor 2 harness connector.

2. Turn ignition switch ON.

3. Check the voltage between exhaust pressure sensor 2 harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

3.CHECK EXHAUST GAS PRESSURE SENSOR 2 GROUND CIRCUIT FOR OPEN AND SHORT

1. Turn ignition switch OFF and wait at least 20 seconds.

2. Check the continuity between exhaust gas pressure sensor 2 harness connector and ECM harness connector.

3. Also check harness for short to ground and short to power.


3. Also check harness for short to ground and short to power.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

4.CHECK EXHAUST GAS PRESSURE SENSOR 2 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1. Check the continuity between exhaust gas pressure sensor 2 harness connector and ECM harness connector.

2. Also check harness for short to ground and short to power.


2. Also check harness for short to ground and short to power.

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

5.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident".

Is the inspection result normal? YES >> Replace exhaust gas pressure sensor 2.

NO >> Repair or replace.

    P0471 exhaust gas pressure sensor 1
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0471 is displayed with DTC P0470 or P2226, first perform trouble diagnosis for DTC P0470 or P2226. Refer to EC-944, "DTC Logic" (P0470), ...

    P047B exhaust gas pressure sensor 2
    DTC Logic DTC DETECTION LOGIC Diagnosis Proce 1.CHECK GROUND CONNECTIONS 1. Turn ignition switch OFF and wait at least 20 seconds. 2. Check ground connection E38. Refer to Ground inspection in ...

    Other materials:

    Types of charge and how to charge the Li-ion battery
    *1: V2X (Vehicle to everything); The EV supplies electric power to a home or a building, etc. (e.g., Vehicle to Home (V2H), Vehicle to Building (V2B), Vehicle to Grid (V2G), Vehicle to Load (V2L), and Vehicle to Vehicle (V2V)). As a fully electric veh ...

    Unlock sensor
    Component Function Check 1.CHECK FUNCTION 1. Select “DOOR LOCK” of “BCM” using CONSULT-III. 2. Select “LOCK STATUS” in “DATA MONITOR” mode. 3. Check that the function operates normally according to the following conditions. Is the inspection result normal? YES >> Unlo ...

    Ignition position warning function does not operate
    Diagnosis Procedure 1.CHECK DTC WITH BCM Check that DTC is not detected with BCM. Is the inspection result normal? YES >> GO TO 2. NO >> Refer to BCS-67, "DTC Index". 2.CHECK POWER DOOR LOCK OPERATION Check power door lock operation. Does door lock/unlock with d ...