Nissan Juke Service and Repair Manual : P0001 fuel pump

DTC Logic

DTC DETECTION LOGIC

NOTE:


NOTE

:
If DTC P0001 is displayed with DTC P0560 or P0657, first perform trouble diagnosis for DTC P0560 or P0657.

Refer to EC-963, "DTC Logic" (DTC P0560) or EC-976, "DTC Logic" (DTC P0657).

Diagnosis Procedure

1.CHECK HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE) POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect high pressure supply pump (volumetric control valve) harness connector.

3. Turn ignition switch ON.

4. Check the voltage between high pressure supply pump (volumetric control valve) harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.DETECT MALFUNCTIONING PART

Check the following.

• Harness or connectors E8, F1 • Harness for open or short between IPDM E/R and high pressure supply pump (volumetric control valve)

>> Repair open circuit or short to ground or short to power in harness or connectors.

3.CHECK HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE) OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between high pressure supply pump (volumetric control valve) harness connector and ECM harness connector.

4. Also check harness for short to ground and short to power.


4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES >> GO TO 4.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

4.CHECK HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE)

Refer to EC-889, "Component Inspection".

Is the inspection result normal? YES >> GO TO 5.

NO >> Replace high pressure supply pump.

5.CHECK FUEL LINE

Check fuel line cleanliness.

Is the inspection result normal? YES >> GO TO 6.

NO >> Fuel line cleanliness.

6.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident", ???INCIDENT SIMULATION TESTS??? and ???GROUND INSPECTION???.

>> INSPECTION END

Component Inspection

1.CHECK HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE)

1. Turn ignition switch OFF.

2. Disconnect high pressure supply pump (volumetric control valve) harness connector.

3. Check resistance between high pressure supply pump (volumetric control valve) terminals as follows.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace high pressure supply pump.

    Power supply and ground circuit
    Diagnosis Procedure 1.INSPECTION START Start engine. Is engine running? YES >> GO TO 6. NO >> GO TO 2. 2.CHECK GROUND CONNECTION-I 1. Turn ignition switch OFF. 2. Check groun ...

    P0002 fuel pump
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0002 is displayed with DTC P0087, P0089, P0090 or P0190, first perform trouble diagnosis for DTC P0087, P0089, P0090 or P0190. Refer to EC-895, " ...

    Other materials:

    B2205 vehicle speed
    Description Vehicle speed signal is transmitted from ABS actuator and electric unit (control unit) via CAN communication to combination meter. DTC Logic DTC DETECTION LOGIC Diagnosis Procedure 1.PERFORM SELF-DIAGNOSIS OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) Perform “Self Diagno ...

    Engine block heater (if so equipped)
    Engine block heaters are used to assist in cold temperature starting. The engine block heater should be used when the outside temperature is 208F (−78C) or lower. To use the engine block heater 1. Turn the engine off. 2. Open the hood and unwrap the engine block heater cord. 3. Plug the ...

    Fuel injector
    Component Function Check 1.INSPECTION START Turn ignition switch to START. Is any cylinder ignited? YES >> GO TO 2. NO >> Go to EC-778, "Diagnosis Procedure". 2.CHECK FUEL INJECTOR FUNCTION With CONSULT-III 1. Start engine. 2. Perform “POWER BALANCE” in “AC ...