Nissan Juke Service and Repair Manual : Transaxle & transmission CVT: RE0F10B
- Precaution
- Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
- Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
- Precaution for Procedure without Cowl Top Cover
- Precaution for On Board Diagnosis (OBD) System of CVT and Engine
- Precaution for TCM and Transaxle Assembly Replacement
- Precaution for G Sensor Removal/Installation or Replacement
- Removal and Installation Procedure for CVT Unit Connector
- Precaution
- Service Notice or Precaution
- ATFTEMP count Conversion Table
- Preparation
- System description
- Ecu diagnosis informatioN
- Wiring diagram
- Basic inspection
- Diagnosis and repair workflow
- Additional service when replacing TCM
- Additional service when replacing transaxle assembly
- Calibration of decel G sensor
- Idle neutral control learning
- CVT fluid
- Stall test
- Line pressure test
- Road test
- CVT position
- DTC/Circuit diagnosis
- U1000 can comm circuit
- U1010 control unit (CAN)
- P0703 brake switch B
- P0705 transmission range switch A
- P0710 transmission fluid temperature sensor A
- P0715 input speed sensor A
- P0717 input speed sensor A
- P0720 output speed sensor
- P0725 engine speed
- P0730 incorrect gear ratio
- P0730 incorrect gear ratio
- P0744 torque converter
- P0745 pressure control solenoid A
- P0746 pressure control solenoid A
- P0776 pressure control solenoid B
- P0778 pressure control solenoid B
- P0826 up and down shift SW
- P0840 transmission fluid pressure SEN/SW A
- P0841 transmission fluid pressure SEN/SW A
- P0868 transmission fluid pressure
- P1585 G sensor
- P1701 TCM
- P1705 TP sensor
- P1722 vehicle speed
- P1723 speed sensor
- P1726 throttle control signal
- P1740 select solenoid
- P1745 line pressure control
- P1777 step motor
- P1778 step motor
- Shift position indicator circuit
- Shift lock system
- Symptom diagnosis
- Removal and installation
- CVT shift selector
- Control cable
- Key interlock cable
- Transmission range switch
- TCM
- Air breather hose
- G sensor
- Control valve
- Primary speed sensor
- Secondary speed sensor
- Differential side oil seal
- Oil pump fitting bolt
- Water hose
- Fluid cooler system
- Unit removal and installation
- Unit disassembly and assembly
- Service data and specifications (SDS)
Service data and specifications (SDS)
General Specifications
...
Precaution
...
Other materials:
Component parts
Component Parts Location
LHD
1. ABS actuator and electric unit (control
unit)
2. Front wheel sensor
3. Stop lamp switch
4. Rear wheel sensor
A. Inside engine room
B. Steering knuckle
C. Brake pedal
D. ABS warning lamp, brake warning
lamp (in combination meter)
E. Rear wheel hub and ...
Removal and installation
IPDM E/R
Exploded View
1. IPDM E/R cover A
2. IPDM E/R
3. IPDM E/R cover B
Removal and Installation
CAUTION:
IPDM E/R integrated relays are not serviceable parts, and must not be removed
from the unit.
REMOVAL
1. Remove battery.
2. Press and expand pawls (A) on lateral side of IPDM E ...
Wheel alignment
Inspection
DESCRIPTION
Measure wheel alignment under unladen conditions.
NOTE:
“Unladen conditions” means that fuel, engine coolant, and lubricant are full.
Spare tire, jack, hand tools and
mats are in designated positions.
PRELIMINARY CHECK
Check the following:
• Tires for impro ...
