Nissan Juke Service and Repair Manual : Shift position indicator circuit

Description

• TCM sends position indicator signals to combination meter by CAN communication line.

• Manual mode switch position is indicated on shift position indicator

Component Function Check

1.CHECK SHIFT POSITION INDICATOR

CAUTION:
Always drive vehicle at a safe speed.

1. Start engine.

2. Check if correct selector lever position (“P”, “N”, “R” or “D”) is displayed as selector lever is moved into each position.

3. Drive vehicle in the manual mode, and confirm that the actual gear position and the meter's indication of the position mutually coincide when the selector lever is shifted to the “UP (+ side)” or “DOWN (− side)” side (1st ⇔ 6th gear).

Is the inspection result normal? YES >> INSPECTION END

NO >> Go to TM-254, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK INPUT SIGNALS

1. Start engine.With CONSULT-III


1. Start engine.

2. Check if correct selector lever position (“P”, “N”, “R” or “D”) is displayed as selector lever is moved into each position.

3. Select “RENGE” on “DATA MONITOR” and read out the value.

4. Drive vehicle in the manual mode, and confirm that the actual gear position and the meter's indication of the position mutually coincide when the selector lever is shifted to the “UP (+ side)” or “DOWN (− side)” side (1st ⇔ 6th gear).

Is the inspection result normal? YES >> INSPECTION END

NO - 1 >> The actual gear position does not change, or shifting into the manual mode is not possible (no gear shifting in the manual mode possible). Or the shift position indicator is not indicated.

• Check manual mode switch. Refer to TM-228, "Component Inspection".

• Check CVT main system (Fail-safe function actuated).

- Perform “SELF-DIAG RESULTS” mode for “TRANSMISSION”. Refer to TM-159, "CONSULT-III Function (TRANSMISSION)".

NO - 2 >> The actual gear position changes, but the shift position indicator is not indicated.

• Perform “SELF-DIAG RESULTS” mode for “TRANSMISSION”. Refer to TM-159, "CONSULT-III Function (TRANSMISSION)".

NO - 3 >> The actual gear position and the indication on the shift position indicator do not coincide.

• Perform “SELF-DIAG RESULTS” mode for “TRANSMISSION”. Refer to TM-159, "CONSULT-III Function (TRANSMISSION)".

NO - 4 >> Only a specific position or positions is/are not indicated on the shift position indicator.

• Check the combination meter. Refer to MWI-23, "CONSULT-III Function".

    P1778 step motor
    Description • The step motor's 4 aspects of ON/OFF change according to the signal from TCM. As a result, the flow of line pressure to primary pulley is changed and pulley ratio is controlled. ...

    Shift lock system
    Component Function Check 1.CHECK SHIFT LOCK OPERATION (PART 1) 1. Turn ignition switch ON. 2. Shift the selector lever to “P” position. 3. Attempt to shift the selector lever to any other than ...

    Other materials:

    Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
    The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. Information necessary to service the system safely is ...

    Battery
    • Keep the battery surface clean and dry. Clean the battery with a solution of baking soda and water. • Make certain the terminal connections are clean and securely tightened. •  If the vehicle is not to be used for 30 days or longer, disconnect the negative battery terminal cable to ...

    Diagnosis systeM (BCM) (without intelligent key system)
    Common item COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) APPLICATION ITEM CONSULT-III performs the following functions via CAN communication with BCM. SYSTEM APPLICATION BCM can perform the following functions for each system. NOTE: It can perform the diagnosis modes except the ...