Nissan Juke Service and Repair Manual : P0725 engine speed

Description

The engine speed signal is transmitted from ECM to TCM by CAN communication line.

DTC Logic

DTC DETECTION LOGI

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

CAUTION:
Always drive vehicle at a safe speed.

NOTE:

If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test.

After the repair, perform the following procedure to confirm the malfunction is eliminated.

1.CHECK DTC DETECTION

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON.

2. Select “DATA MONITOR” in “TRANSMISSION”.

3. Start engine and maintain the following conditions for at least 10 consecutive seconds.

PRI SPEED SEN : More than 1000 rpm

Is “P0725” detected? YES >> Go to TM-212, "Diagnosis Procedure".

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

Diagnosis Procedure

1. CHECK DTC WITH ECM

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON.

2. Select “SELF-DIAG RESULTS” in “ENGINE”.

Is the inspection result normal? YES >> GO TO 2.

NO >> Check the DTC detected item. Refer to EC-83, "CONSULT-III Function".

2. CHECK DTC WITH TCM

Select “SELF-DIAG RESULTS” in “TRANSMISSION”.With CONSULT-III


Select “SELF-DIAG RESULTS” in “TRANSMISSION”.

Is the inspection result normal? YES >> GO TO 3.

NO >> Check the DTC detected item. Refer to TM-159, "CONSULT-III Function (TRANSMISSION)".

3. CHECK INPUT SIGNALS

1. Start engine.With CONSULT-III


1. Start engine.

2. Select “DATA MONITOR” in “TRANSMISSION”.

3. While monitoring “ENG SPEED SIG”, check for engine speed change corresponding to “ACC PEDAL OPEN”.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> Check ignition signal circuit. Refer to EC-414, "Component Function Check".

4. CHECK TCM

Check TCM input/output signals. Refer to TM-164, "Reference Value".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Replace the TCM. Refer to TM-280, "Removal and Installation".

    P0720 output speed sensor
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE CAUTION: Always drive vehicle at a safe speed. NOTE: If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignit ...

    P0730 incorrect gear ratio
    Description TCM selects the gear ratio using the engine load (throttle position), the primary pulley revolution speed, and the secondary pulley revolution speed as input signal. Then it changes th ...

    Other materials:

    License plate lamp
    Exploded View 1. License plate lamp housing assembly 2. Blub 3. License plate lamp blub socket : Pawl Removal and Installation CAUTION: Disconnect battery negative terminal or remove the fuse. REMOVAL 1. While pressing the license plate lamp to direction right side, pull it to directio ...

    B2612 steering status
    DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B2612 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to BCS-83, "DTC Logic". • If DTC B2612 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to BCS-84, "D ...

    When traveling or registering your vehicle in another country
    When planning to travel in another country, you should first find out if the fuel available is suitable for your vehicle’s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline. Therefore, avoid taking yo ...