Nissan Juke Service and Repair Manual : P0778 pressure control solenoid B

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

NOTE

:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test.

After the repair, perform the following procedure to confirm the malfunction is eliminated.

1.CHECK DTC DETECTION

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON.

2. Start engine.

3. Drive vehicle and maintain the following conditions for at least 5 consecutive seconds.

4. Select “Self Diagnostic Results” in “TRANSMISSION”.

Follow the procedure “With CONSULT-III”.With GST


Follow the procedure “With CONSULT-III”.

Is “P0778” detected? YES >> Go to TM-225, "Diagnosis Procedure".

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

Diagnosis Procedure

1.CHECK SECONDARY PRESSURE SOLENOID VALVE CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect TCM connector.

3. Check resistance between TCM connector terminal and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> GO TO 2.

2.CHECK SECONDARY PRESSURE SOLENOID VALVE

Check secondary pressure solenoid valve. Refer to TM-226, "Component Inspection".

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace damaged parts.

3.CHECK HARNESS BETWEEN TCM AND SECONDARY PRESSURE SOLENOID VALVE

1. Turn ignition switch OFF.

2. Disconnect TCM connector and CVT unit harness connector.

3. Check continuity between TCM connector terminal and CVT unit harness connector terminal.

4. If OK, check harness for short to ground and short to power.


4. If OK, check harness for short to ground and short to power.

5. Reinstall any part removed.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace damaged parts.

4.CHECK TCM

Check TCM input/output signals. Refer to TM-164, "Reference Value".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Replace the TCM. Refer to TM-280, "Removal and Installation".

Component Inspection

SECONDARY PRESSURE SOLENOID VALVE

1.SECONDARY PRESSURE SOLENOID VALVE

1. Turn ignition switch OFF.

2. Disconnect CVT unit harness connector.

3. Check resistance between CVT unit harness connector terminal and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace the transaxle assembly. Refer to TM-301, "Removal and Installation".

    P0776 pressure control solenoid B
    Description The secondary pressure solenoid valve regulates the secondary pressure to suit the driving condition in response to a signal sent from the TCM. DTC Logic DTC DETECTION LOGIC DTC C ...

    P0826 up and down shift SW
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE CAUTION: Always drive vehicle at a safe speed. NOTE: If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn i ...

    Other materials:

    Meters and Gauges
    Vehicle information display: Digital clock Outside air temperature reading Li-ion battery available charge gauge Estimated driving range Odometer and twin trip odometer readings Charging tim ...

    P1197 out of gas
    Description This diagnosis result is detected when the fuel level of the fuel tank is extremely low and the engine does not run normally. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING 1. Turn ignition switch OFF and wait at least 10 seconds. 2. Turn ignition ...

    Removal and Installation
    REMOVAL 1. Shift the transaxle to the neutral position, and then release the parking brake. 2. Put matching marks on propeller shaft flange yoke and final drive companion flanges. CAUTION: For matching marks, use paint. Never damage propeller shaft flange yoke and final drive companion ...