Nissan Juke Service and Repair Manual : Security Control System with intelligent key system
- Precaution
- Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
- Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
- Precaution for Procedure without Cowl Top Cover
- System description
- ECU diagnosis information
- Wiring diagram
- Basic inspection
- DTC/circuit diagnosis
- P1610 lock mode
- P1611 ID discord, IMMU-ECM
- P1612 chain of ECM-IMMU
- P1614 chain of IMMU-KEY
- P1616 ECM
- B2192 ID discord, IMMU-ECM
- B2193 chain of ECM-IMMU
- B2195 anti-scanning
- B2196 dongle unit
- B2198 nats antenna AMP.
- B2013 steering lock unit
- B2014 chain of STRG-IMMU
- B2555 stop lamp
- B2556 Push-button ignition switch
- B2557 vehicle speed
- B2601 shift position
- B2602 shift position
- B2603 shift position
- B2604 shift position
- B2605 shift position
- B2608 starter relay
- B2609 steering status
- B260B steering lock unit
- B260C steering lock unit
- B260F Engine status
- B2612 steering status
- B2619 BCM
- B261A Push-button ignition switch
- B261F ASCD clutch switch
- B2620 Park/neutral position switch
- B26E8 clutch interlock switch
- B26E9 steering status
- B26EF steering lock relay
- B26F0 steering lock relay
- B26F3 starter control relay
- B26F4 starter control relay
- B26F5 steering lock status switch
- B26F7 BCM
- B26F8 BCM
- B26F9 cranking request circuit
- B26FA cranking request circuit
- B26FB clutch switch
- B26FC key registration
- B209F cranking request circuit
- B20A0 cranking request circuit
- B2108 steering lock relay
- B2109 steering lock relay
- B210A steering lock unit
- B210B starter control relay
- B210C starter control relay
- B210D starter relay
- B210E starter relay
- B210F shift position/clutch interlock switch
- B2110 shift position/clutch interlock switch
- Hood switch
- Horn function
- Security indicator lamp
- Symptom diagnosis
- Engine does not start when intelligent key is inside of vehicle
- Steering does not lock
- Security indicator lamp does not turn on or blink
- Vehicle security system cannot BE set
- Vehicle security alarm does not activate
- Removal and installation
Keyfob battery
Exploded View
1. Upper case
2. Key
3. Switch cover
4. Switch rubber
5. Board surface
6. Battery
7. plate
8. Lower case
9. Screw
Removal and Installation
REMOVAL
1. Remove screw (9) ...
Precaution
...
Other materials:
Clutch pedal position switch
Component Function Check
1.CHECK FOR CLUTCH PEDAL POSITION SWITCH FUNCTION
1. Turn ignition switch ON.
2. Check the voltage between ECM harness connector and ground.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Proceed to EC-427, "Diagnosis Procedure" ...
P0409 EGR volume control valve control position sensor
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF.
2. Check ground connection E38. Refer to Ground inspection in GI-44, "Circuit
Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or ...
HR16DE : Removal and Installation
REMOVAL
1. Disconnect the battery cable from the negative terminal. Refer to PG-124,
"Removal and Installation".
2. Remove radiator reservoir tank. Refer to CO-17, "Exploded View".
3. Disconnect harness connectors (1) from battery terminal with
fusible link.
4. Remove harn ...
