Nissan Juke Service and Repair Manual : Vehicle security system cannot BE set
INTELLIGENT KEY
INTELLIGENT KEY : Description
Armed phase is not activated when door is locked using Intelligent Key.
NOTE
:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE
(OPERATING CONDITIONS)”
before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using CONSULT-III.
INTELLIGENT KEY : Diagnosis Procedure
1.CHECK INTELLIGENT KEY SYSTEM (REMOTE KEYLESS ENTRY FUNCTION)
Lock/unlock door with Intelligent Key.
Refer to DLK-28, "DOOR LOCK FUNCTION : System Description" (With super lock) or DLK-205, "DOOR LOCK FUNCTION : System Description" (Without super lock).
Is the inspection result normal? YES >> GO TO 2.
NO >> Check Intelligent Key system (remote keyless entry function). Refer to DLK-113, "Diagnosis Procedure" (With super lock) or DLK-279, "Diagnosis Procedure" (Without super lock).
2.CHECK HOOD SWITCH
Check hood switch.
Refer to SEC-155, "Component Function Check".
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace hood switch.
3.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> GO TO 1.
Door request switch
DOOR REQUEST SWITCH : Description
Armed phase is not activated when door is locked using door request switch.
NOTE
:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE
(OPERATING CONDITIONS)”
before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using CONSULT-III.
DOOR REQUEST SWITCH : Diagnosis Procedure
1.CHECK INTELLIGENT KEY SYSTEM (DOOR LOCK FUNCTION)
Lock/unlock door with door request switch.
Refer to DLK-28, "DOOR LOCK FUNCTION : System Description" (With super lock) or DLK-205, "DOOR LOCK FUNCTION : System Description" (Without super lock).
Is the inspection result normal? YES >> GO TO 2.
NO >> Check Intelligent Key system (door lock function). Refer to DLK-106, "ALL DOOR REQUEST SWITCHES : Diagnosis Procedure" (With super lock) or DLK-272, "ALL DOOR REQUEST SWITCHES : Diagnosis Procedure" (Without super lock).
2.CHECK HOOD SWITCH Check hood switch.
Refer to SEC-155, "Component Function Check".
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace hood switch.
3.CONFIRM THE OPERATION Confirm the operation again.
Is the result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> GO TO 1.
Unlock sensor
UNLOCK SENSOR : Description
Armed phase is not activated when door is locked by door key cylinder operation using mechanical key.
NOTE
:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE
(OPERATING CONDITIONS)”
before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using CONSULT-III.
UNLOCK SENSOR : Diagnosis Procedure
1.CHECK DOOR LOCK FUNCTION
Lock/unlock door using meahanical key inserted into door key cylinder.
Refer to DLK-24, "System Description" (With super lock), DLK-201, "System Description" (Without super lock).
Is the inspection result normal? YES >> GO TO 2.
NO >> Check Intelligent Key system (remote keyless entry function). Refer to DLK-109, "Diagnosis Procedure" (With super lock) or DLK-275, "Diagnosis Procedure" (Without super lock).
2.CHECK HOOD SWITCH
Check hood switch.
Refer to SEC-155, "Component Function Check".
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace hood switch.
3.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> GO TO 1.
Security indicator lamp does not turn on or blink
Description
Security indicator lamp does not blink when ignition switch is in a position
other than ON.
NOTE:
• Before performing the diagnosis, check “Work Flow”. Refer to SEC-47, " ...
Vehicle security alarm does not activate
Description
Alarm does not operate when alarm operating condition is satisfied.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE
(OPERATING CONDITIONS)”
befo ...
Other materials:
B1135 side air bag module LH
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT
With CONSULT-III
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.
Without CONSULT-III
1. Turn ignition switch ON.
2. Check the air bag warning la ...
Refrigerant pressure sensor
Component Function Check
1.CHECK REFRIGERANT PRESSURE SENSOR OVERALL FUNCTION
1. Start engine and warm it up to normal operating temperature.
2. Turn A/C switch and blower fan switch ON.
3. Check the voltage between ECM harness connector and ground.
Is the inspection result normal?
YES >& ...
Component parts
Automatic air conditioning system : Component Parts Location
1. BCM
• With Intelligent Key: Refer to BCS-
6, "BODY CONTROL SYSTEM :
Component Parts Location".
• Without Intelligent Key: Refer to
BCS-96, "BODY CONTROL SYSTEM
: Component Parts Location".
2. Magnet clu ...
