Nissan Juke Service and Repair Manual : B26E8 clutch interlock switch

DTC Logic

NOTE

:
• If DTC B26E8 is displayed with DTC B210F, first perform the trouble diagnosis for DTC B210F. Refer to BCS-83, "DTC Logic".

• If DTC B26E8 is displayed with DTC B2110, first perform the trouble diagnosis for DTC B2110. Refer to BCS-84, "DTC Logic".

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION PROCEDURE 1

1. Turn ignition switch ON and wait 2 seconds or more under the following conditions.

- Shift lever: In the neutral position.

- Clutch pedal: Depressed 2. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT-III.

Is DTC detected? YES >> Go to SEC-113, "Diagnosis Procedure".

NO >> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE 2

1. Release clutch pedal and wait 2 seconds or more.

2. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT-III.

Is DTC detected? YES >> Go to SEC-113, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.INSPECTION START

Perform inspection in accordance with procedure that confirms DTC.

Which procedure confirms DTC? DTC confirmation procedure 1>>GO TO 2.

DTC confirmation procedure 2>>GO TO 3.

2.CHECK CLUTCH PEDAL POSITION SWITCH CIERCUIT

Refer to EC-427, "Component Function Check" (MR16DDT), EC-771, "Component Function Check" (HR16DE), or EC-980, "DTC Logic" (K9K).

Is the inspection result normal? YES >> GO TO 8.

NO >> Repair or replace the malfunctioning parts.

3.CHECK CLUTCH INTERLOCK SWITCH POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect clutch interlock switch connector 3. Check voltage between clutch interlock switch harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO-1 >> Check 10 A fuse [No. 13, located in the fuse block (J/B)] NO-2 >> Check harness for open or short between clutch interlock switch and fuse.

4.CHECK CLUTCH INTERLOCK SWITCH SIGNAL

1. Connect clutch interlock switch connector.

2. Check voltage between BCM harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 8.

NO >> GO TO 5.

5.CHECK CLUTCH INTERLOCK SWITCH SIGNAL CIRCUIT

1. Disconnect clutch interlock switch connector.

2. Disconnect BCM connector.

3. Check continuity between clutch interlock switch harness connector and BCM harness connector.

4. Check continuity between clutch interlock switch harness connector and


4. Check continuity between clutch interlock switch harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace harness.

6.CHECK CLUTCH INTERLOCK SWITCH

Refer to SEC-115, "Component Inspection".

Is the inspection result normal? YES >> GO TO 7.

NO >> Replace clutch interlock switch. Refer to CL-16, "LHD : Removal and Installation" (LHD) or CL-18, "RHD : Removal and Installation" (RHD).

7.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident".

>> INSPECTION END

8.REPLACE BCM

1. Replace BCM. Refer to BCS-93, "Removal and Installation".

2. Perform initialization of BCM and reregistration of all Intelligent Key using CONSULT-III.

For initialization and reregistration procedures, refer to CONSULT-III Operation Manual NATS-IVIS/NVIS.

>> INSPECTION END

Component Inspection

1.CHECK CLUTCH INTERLOCK SWITCH

1. Turn ignition switch OFF.

2. Disconnect clutch interlock switch connector.

3. Check continuity between clutch interlock switch terminals.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace clutch interlock switch. Refer to CL-16, "LHD : Removal and Installation" (LHD) or CL-18, "RHD : Removal and Installation" (RHD).

    B2620 Park/neutral position switch
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE 1. Turn ignition switch ON and wait 2 seconds or more under the following conditions. 2. Set shif ...

    B26E9 steering status
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE 1. Turn ignition switch ON. 2. Turn ignition switch OFF. 3. Press driver side door switch. 4. Tur ...

    Other materials:

    CVT position
    Inspection and Adjustment INSPECTION 1. Place selector lever in “P” position, and turn ignition switch ON (engine stop). 2. Make sure that selector lever can be shifted to other than “P” position when brake pedal is depressed. Also make sure that selector lever can be shifted from ...

    Safety note
    WARNING • Do not disassemble or modify this system. If you do, it may result in accidents, fire, or electric shock. • Do not use this system if you notice any abnormality, such as a frozen screen or lack of sound. Continued use of the system may result in accident, fire or electric shock ...

    B2556 Push-button ignition switch
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE 1. Press push-button ignition switch under the following condition. - Brake pedal: Not depressed 2. Release push-button ignition switch and wait 100 seconds or more. 3. Check DTC in “Self Diagnos ...