Nissan Juke Service and Repair Manual : B2608 starter relay

DTC Logic

DTC DETECTION LOGIC

NOTE

:
• If DTC B2608 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to BCS-83, "DTC Logic".

• If DTC B2608 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to BCS-84, "DTC Logic".

• If DTC B2608 is displayed with DTC B210D (IPDM E/R), first perform the trouble diagnosis for DTC B210D.

Refer to SEC-146, "DTC Logic".

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION PROCEDURE

1. Press push-button ignition switch under the following conditions to start engine.

- Selector lever: In the P position - Brake pedal: Depressed 2. Wait 1 second after engine started.

3. Check DTC in “Self Diagnostic Result� mode of “BCM� using CONSULT-III.

Is DTC detected? YES >> Go to SEC-93, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK DTC OF IPDM E/R

Check DTC in “Self Diagnostic Result� mode of “IPDM E/R� using CONSULT-III.

Is DTC detected? YES >> Perform the trouble diagnosis related to the detected DTC. Refer to PCS-25, "DTC Index".

NO >> GO TO 2.

2.CHECK STARTER RELAY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Disconnect BCM connector.

4. Check continuity between IPDM E/R harness connector and BCM harness connector.

5. Check continuity between IPDM E/R harness connector and ground.


5. Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?


Is the inspection result normal?

YES >> GO TO 3.

NO >> Repair or replace harness.

3.REPLACE IPDM E/R

1. Replace IPDM E/R. Refer to PCS-34, "Removal and Installation".

2. Perform DTC CONFIRMATION PROCEDURE for DTC B2608. Refer to SEC-93, "DTC Logic".

Is DTC B2608 detected again? YES >> INSPECTION END

NO >> GO TO 4.

4.REPLACE BCM

1. Replace BCM. Refer to BCS-93, "Removal and Installation".

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT-III.

For initialization and registration procedures, refer to CONSULT-III Operation Manual NATS-IVIS/NVIS.

>> INSPECTION END

    B2605 shift position
    DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B2605 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to BCS-83, "DTC Logic". • If DTC B2605 is ...

    B2609 steering status
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE 1 1. Press push-button ignition switch under the following conditions and wait 1 second or more. ...

    Other materials:

    Locking with key
    The power door lock system allows you to lock or unlock all doors simultaneously. •  Turning the driver’s door key cylinder to the front of the vehicle1 will lock all doors and the lift gate. • Turning the driver’s door key cylinder once to the rear of the vehicle2 will unlock t ...

    U1405 engine torque signal
    DTC Logic DTC DETECTION LOGIC Diagnosis Procedure 1.PERFORM ECM SELF-DIAGNOSIS Using CONSULT-III, check the “self diagnosis result� of “ENGINE� and repair or replace any malfunctioning parts. >> • Refer to EC-108, "DTC Index". (MR16DDT) • Refer to EC-522, &qu ...

    P1554 battery current sensor
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM COMPONENT FUNCTION CHECK Perform component function check. Refer to EC-337, "Component Function Check". NOTE: Use component function check to check the overall function of the battery current sensor circuit. D ...