Nissan Juke Service and Repair Manual : DTC/circuit diagnosis
- Trouble diagnosis - specification valuE
- Power supply and ground circuit
- U1000, U1001 CAN COMM CIRCUIT
- P0011 IVT control
- P0014 EVT control
- P0031, P0032 A/F sensor 1 heater
- P0037, P0038 HO2S2 heater
- P0075 IVT control solenoid valve
- P0078 EVT control solenoid valve
- P0102, P0103 MAF SENSOR
- P0112, P0113 IAT SENSOR
- P0117, P0118 ECT SENSOR
- P0122, P0123 TP SENSOR
- P0130 A/F sensor 1
- P0131 A/F sensor 1
- P0132 A/F sensor 1
- P0133 A/F sensor 1
- P0137 HO2S2
- P0138 HO2S2
- P0139 HO2S2
- P0171 fuel injection system function
- P0172 fuel injection system function
- P0197, P0198 EOT sensor
- P0222, P0223 TP sensor
- P0300, P0301, P0302, P0303, P0304 misfire
- P0327, P0328 KS
- P0335 CKP sensor (POS)
- P0340 CMP sensor (phase)
- P0420 three way catalyst function
- P0444 EVAP canister purge volume control solenoid valve
- P0500 VSS
- P0520 EOP sensor
- P0524 engine oil pressure
- P0603 ECM
- P0605 ECM
- P0607 ECM
- P0643 sensor power supply
- P0850 PNP switch
- P1212 TCS communication line
- P1217 engine over temperature
- P1220 fuel pump control module (FPCM)
- P1225 TP sensor
- P1226 TP sensor
- P1550 battery current sensor
- P1551, P1552 battery current sensor
- P1553 battery current sensor
- P1554 battery current sensor
- P1556, P1557 battery temperature sensor
- P1564 ASCD steering switch
- P1572 ASCD brake switch
- P1574 ASCD vehicle speed sensor
- P1650 starter motor relay 2
- P1651 starter motor relay
- P1652 starter motor system COMM
- P1715 input speed sensor
- P1805 brake switch
- P2100, P2103 throttle control motor relay
- P2101 electric throttle control function
- P2118 throttle control motor
- P2119 electric throttle control actuator
- P2122, P2123 APP sensor
- P2127, P2128 APP sensor
- P2135 TP sensor
- P2138 APP sensor
- P2A00 A/F sensor 1
- ASCD brake switch
- ASCD indicator
- ASCD main switch
- Clutch pedal position switch
- Cooling fan
- Electrical load signal
- Fuel injector
- Fuel pump
- Ignition signal
- Information display (speed limiter)
- Malfunction indicator
- Refrigerant pressure sensor
- Speed limiter main switch
How to set SRT code
Description
OUTLINE
In order to set all SRTs, the self-diagnoses as in the “SRT ITEM” table must
have been performed at least
once. Each diagnosis may require actual driving for a long period of ...
Trouble diagnosis - specification valuE
Description
The specification (SP) value indicates the tolerance of the value that is
displayed in “SPEC” of “DATA MONITOR”
mode of CONSULT-III during normal operation of the Engine Control System ...
Other materials:
EPS warning lamp does not turn off
Description
EPS warning lamp does not turn OFF several seconds after engine started.
Diagnosis Procedure
1.PERFORM SELF-DIAGNOSIS
With CONSULT-III
1. Turn the ignition switch OFF to ON.
2. Perform “EPS” self-diagnosis.
Is any DTC detected?
YES >> Check the DTC. Refer to STC-14, " ...
Service Notice or Precautions for EPS System
• Check the following item when performing the trouble diagnosis.
- Check any possible causes by interviewing the symptom and it′s condition from
the customer if any malfunction,
such as EPS warning lamp is turned ON, occurs.
- Check if air pressure and size of tires are proper, the spe ...
Door mirror system (with intelligent key)
LHD
LHD : Wiring Diagram
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to GI-12, "Connector Information/Explanation
of Option Abbreviation".
RHD
RHD : Wiring Diagram
For connector termina ...
