Nissan Juke Service and Repair Manual : The seat belt reminder warning continues sounding, or does not sound
Description
• Seat belt reminder warning does not sound.
• Seat belt reminder warning sounds continuously.
Diagnosis Procedure
1.CHECK SEAT BELT WARNING LAMP
1. Turn ignition switch ON.
2. Check the operation of the seat belt warning lamp in the combination meter.
Seat belt (driver side) fastened : OFF Seat belt (driver side) unfastened : ON Seat belt (passenger side) fastened* : OFF Seat belt (passenger side) unfastened* : ON
*: When getting in the passenger seat Is the inspection result normal? YES >> Replace combination meter. Refer to MWI-69, "Removal and Installation".
NO >> GO TO 2.
2.CHECK SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT (DRIVER SIDE)
Perform the check for the seat belt buckle switch (driver side) circuit. Refer to MWI-58, "Diagnosis Procedure".
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)
Perform the check for the seat belt buckle switch (driver side). Refer to MWI-59, "Component Inspection".
Is the inspection result normal? YES >> GO TO 4.
NO >> Replace seat belt buckle (driver side). Refer to SB-8, "SEAT BELT BUCKLE : Removal and Installation".
4.CHECK SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT (PASSENGER SIDE)
Perform the check for the seat belt buckle switch (passenger side) circuit. Refer to MWI-60, "Diagnosis Procedure".
Is the inspection result normal? YES >> GO TO 5.
NO >> Repair harness or connector.
5.CHECK SEAT BELT BUCKLE SWITCH (PASSENGER SIDE)
Perform the check for the seat belt buckle switch (passenger side). Refer to MWI-60, "Component Inspection (Seat Belt Buckle Switch)".
Is the inspection result normal? YES >> GO TO 6.
NO >> Replace seat belt buckle (passenger side). Refer to SB-8, "SEAT BELT BUCKLE : Removal and Installation".
6.CHECK OCCUPANT DETECTION UNIT
Perform the check for the occupant detection unit. Refer to MWI-61, "Component Inspection (Occupant Detection Unit)".
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-69, "Removal and Installation".
NO >> Replace seat cushion trim and pad. Refer to SE-21, "SEAT CUSHION : Disassembly and Assembly" (2WD) or SE-29, "SEAT CUSHION : Disassembly and Assembly" (4WD).
The light reminder warning does not sound
Description
Light reminder warning chime does not sound even though headlamp is
illuminated.
Diagnosis Procedure
1.CHECK COMBINATION SWITCH (LIGHTING SWITCH) OPERATION
Check that the headlamps o ...
The key warning does not sound (without intelligent key)
Description
The key warning chime does not sound, when all of the following conditions
are fulfilled.
• Key inserted into the key cylinder (key switch signal ON).
• Ignition switch is in AC ...
Other materials:
Structure and operation
Positive Crankcase Ventilation
This system returns blow-by gas to the intake manifold.
The positive crankcase ventilation (PCV) valve is provided to conduct crankcase
blow-by gas to the intake
manifold.
During partial throttle operation of the engine, the intake manifold sucks the
blow ...
Measurement of weights
Secure loose items to prevent weight shifts that could affect the balance of
your vehicle. When the vehicle is loaded, drive to a scale and weigh the front and
the rear wheels separately to determine axle loads.
Individual axle loads should not exceed either of the Gross Axle Weight Ratings
( ...
C1130 engine signal
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn
ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CON ...
