Nissan Juke Service and Repair Manual : Rear door lock

Exploded View

1. Outside handle assembly


1. Outside handle assembly 2. Inside handle
3. TORX bolt
4. Door lock assembly
5. Rear door sealing screen

: Pawl: Clip
: Vehicle front: Pawl
: Do not reuse: Vehicle front
: N·m (kg-m, in-lb): Do not reuse
: Body grease: N·m (kg-m, in-lb)
Door lock: Body grease


Door lock

DOOR LOCK : Removal and Installation

REMOVAL

1. Remove rear door glass and rear door lower sash (rear). Refer to GW-21, "Removal and Installation".

2. Remove inside handle. Refer to DLK-180, "INSIDE HANDLE : Removal and Installation".

3. Remove outside handle. Refer to DLK-180, "OUTSIDE HANDLE : Removal and Installation".

4. Remove door lock assembly TORX bolts.

5. Disconnect door lock actuator connector, and then remove door lock assembly.

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:
• Never reuse TORX bolt. Always replace it with a new one when it is removed.

• Check door open/close, lock/unlock operation after installation.

• Check door lock assembly for poor lubrication. Apply body grease to door lock if necessary.

: Grease up point


Inside handle


Inside handle

INSIDE HANDLE : Removal and Installation

REMOVAL

1. Remove rear door finisher. Refer to INT-16, "Removal and Installation".

2. Remove upper side of sealing screen.

NOTE

:
Cut the butyl tape so that some parts of the butyl tape do not remain on the sealing screen, if the sealing screen is reused.

3. Remove inside handle mounting bolt (A).

4. Disengage inside handle (1) from door panel (2) while sliding inside handle toward vehicle rear, and then separate inside handle.

: Vehicle front


5. Disengage inside handle cable (2), and then remove inside handle


5. Disengage inside handle cable (2), and then remove inside handle (1).

INSTALLATION


INSTALLATION

Note the following item, and install in the reverse order of removal.

CAUTION:
Check door open/close, lock/unlock operation after installation.

Outside handle

OUTSIDE HANDLE : Removal and Installation

REMOVAL

1. Remove rear door finisher and rear door corner cover inner. Refer to INT-16, "Removal and Installation".

2. Remove rear door sealing screen.

3. Rotate stopper (1) upward.

4. Disengage outside handle cable (2), and then remove outside handle cable from outside handle assembly (3).

5. Remove outside handle assembly mounting bolts (A).


5. Remove outside handle assembly mounting bolts (A).

6. Disengage mounting clips using a remover tool (A), and then


6. Disengage mounting clips using a remover tool (A), and then remove outside handle assembly.

CAUTION:
Apply protective tape (B) on the door panel to protect the painted surface from damage.

: Clip


INSTALLATION: Clip


INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:
• Never reuse rear door sealing screen. Always replace it with a new one when it is removed.

When installing rear door sealing screen, install it according to the following procedure.

- Put lower portion of rear door sealing screen (1) into inside of door panel (2).

- Perform positioning according to the following procedure, and then install rear door sealing screen.

• Align upper portion of rear door sealing screen to hole (A) of door panel as shown in the figure.

• Align hole of rear door sealing screen to edge (B) of door panel as shown in the figure.

• Be careful to position outside handle cable normally when installing it.


• Be careful to position outside handle cable normally when installing it. For details, refer to DLK-179, "Exploded View".

• Check door open/close, lock/unlock operation after installation.

    Front door lock
    Exploded View 1. Door key cylinder assembly (driver side) Outside handle escutcheon (passenger side) 2. Outside handle 3. Front gasket 4. Inside handle 5. TORX bolt 6. Door lock assembly ...

    Back door lock
    Exploded View 1. Back door lock assembly 2. TORX bolt 3. Back door striker : Do not reuse : N·m (kg-m, ft-lb) : Body grease Door lock DOOR LOCK : Removal and Installation REMOVAL 1. Rem ...

    Other materials:

    Air fresheners
    Most air fresheners use a solvent that could affect the vehicle interior. If you use an air freshener, take the following precautions: • Hanging-type air fresheners can cause permanent discoloration when they contact vehicle interior surfaces. Place the air freshener in a location that allows ...

    Brake fluid
    Inspection BRAKE FLUID LEVEL • Check that the fluid level in the reservoir tank is within the specified range (MAX – MIN lines). • Visually check for any brake fluid leakage around the reservoir tank. • Check the brake system for any leakage if the fluid level is extremely low (lower ...

    Intelligent key battery
    Removal and Installation 1. Release the lock knob at the back of the Intelligent Key and remove the mechanical key. 2. Insert a flat-blade screwdriver (A) wrapped with a cloth into the slit of the corner and twist it to separate the upper part from the lower part. CAUTION: • Do not touch ...