Nissan Juke Service and Repair Manual : P181B incomplete selfshut

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.DTC REPRODUCTION PROCEDURE

1. Turn the ignition switch OFF.With CONSULT-III


1. Turn the ignition switch OFF.

2. Perform self-diagnosis for “ALL MODE AWD/4WD”.

Is DTC “P181B” detected? YES >> Proceed to diagnosis procedure. Refer to DLN-47, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK 4WD CONTROL MODULE POWER SUPPLY (1)

1. Turn the ignition switch OFF.

2. Disconnect 4WD control module harness connector.

3. Check the voltage between 4WD control module harness connector and ground.

4. Turn the ignition switch ON.


4. Turn the ignition switch ON.

CAUTION:
Never start the engine

.

5. Check the voltage between 4WD control module harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK 4WD CONTROL MODULE POWER SUPPLY (2)

1. Turn the ignition switch OFF.

2. Check the 10A fuse (#33).

3. Check the harness for open or short between 4WD control module harness connector No.1 terminal and 10A (#33).

Is the inspection result normal?

YES >> Perform the trouble diagnosis for power supply circuit. Refer to PG-10, "Wiring Diagram - BATTERY POWER SUPPLY -".

NO >> Repair or replace error-detected parts.

3.CHECK 4WD CONTROL MODULE GROUND

1. Turn the ignition switch OFF.

2. Check the continuity between 4WD control module harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace error-detected parts.

4.CHECK TERMINALS AND HARNESS CONNECTORS

Check 4WD control module pin terminals for damage or loose connection with harness connector.

Is inspection result normal? YES >> After turning the ignition switch OFF, perform DTC confirmation procedure again. When DTC “P181B” is detected, Replace 4WD control module. Refer to DLN-91, "Removal and Installation".

NO >> Repair or replace error-detected parts.

    P1813 4WD mode switch
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least ...

    P181D engine torque signal
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least ...

    Other materials:

    Diagnosis system (bcm) (with intelligent key system)
    Common item COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) APPLICATION ITEM CONSULT-III performs the following functions via CAN communication with BCM. SYSTEM APPLICATION BCM can perform the following functions for each system. NOTE: It can perform the diagnosis modes except the ...

    Idle speed
    Description This describes how to check the idle speed. For the actual procedure, follow the instructions in “BASIC INSPECTION”. Special Repair Requirement 1.CHECK IDLE SPEED With CONSULT-III Check idle speed in “DATA MONITOR” mode with CONSULT-III. With GST Check idle speed wit ...

    Control linkage
    Exploded View 1. Bracket 2. Selector cable 3. Shifter lever A 4. Selector lever 5. Cable mounting bracket 6. Tapping bolt 7. Shifter cable 8. Grommet 9. M/T shift selector assembly 10. Shifter lever 11. Shifter lever knob : Always replace after every disassembly. : N·m (kg-m ...