Nissan Juke Service and Repair Manual : Vehicle security system cannot be set
Key fob
KEY FOB : Description
Armed phase is not activated when door is locked using keyfob.
NOTE
:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE
(OPERATING CONDITIONS)”
before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using CONSULT-III.
KEY FOB : Diagnosis Procedure
1.CHECK REMOTE KEYLESS ENTRY SYSTEM
Lock/unlock door with keyfob.
Refer to DLK-366, "REMOTE KEYLESS ENTRY FUNCTION : System Description" (With super lock) or DLK- 497, "System Description" (Without super lock).
Is the inspection result normal? YES >> GO TO 2.
NO >> Check remote keyless entry system. Refer to DLK-418, "Diagnosis Procedure" (With super lock) or DLK-538, "Diagnosis Procedure" (Without super lock).
2.CHECK HOOD SWITCH
Check hood switch.
Refer to SEC-223, "Component Function Check".
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace hood switch.
3.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> GO TO 1.
Door lock and unlock switch
DOOR LOCK AND UNLOCK SWITCH : Description
Armed phase is not activated when door is locked using door lock and unlock switch.
NOTE
:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE
(OPERATING CONDITIONS)”
before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using CONSULT-III.
DOOR LOCK AND UNLOCK SWITCH : Diagnosis Procedure
1.CHECK POWER DOOR LOCK SYSTEM (DOOR LOCK FUNCTION)
Lock/unlock door with door lock and unlock switch.
Refer to DLK-363, "System Description" (With super lock) or DLK-494, "System Description" (Without super lock).
Is the inspection result normal? YES >> GO TO 2.
NO >> Check power door lock system (door lock function). Refer to DLK-415, "ALL DOOR : Diagnosis Procedure" (With super lock) or DLK-534, "ALL DOOR : Diagnosis Procedure" (Without super lock).
2.CHECK HOOD SWITCH
Check hood switch.
Refer to SEC-223, "Component Function Check".
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace hood switch.
3.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> GO TO 1.
Unlock sensor
UNLOCK SENSOR : Description
Armed phase is not activated when door is locked by door key cylinder operation using mechanical key.
NOTE
:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE
(OPERATING CONDITIONS)”
before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using CONSULT-III.
UNLOCK SENSOR : Diagnosis Procedure
1.CHECK POWER DOOR LOCK SYSTEM (DOOR LOCK FUNCTION)
Lock/unlock door using mechanical key inserted into door key cylinder.
Refer to DLK-363, "System Description" (With super lock) or DLK-494, "System Description" (Without super lock).
Is the inspection result normal? YES >> GO TO 2.
NO >> Check power door lock system (door lock function). Refer to DLK-414, "Diagnosis Procedure" (With super lock) or DLK-537, "Diagnosis Procedure" (Without super lock).
2.CHECK HOOD SWITCH
Check hood switch.
Refer to SEC-223, "Component Function Check".
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace hood switch.
3.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> GO TO 1.
Security indicator lamp does not turn on or blink
Description
Security indicator lamp does not blink when ignition switch is in a position
other than ON.
NOTE:
• Before performing the diagnosis, check “Work Flow”. Refer to SEC-187, " ...
Vehicle security alarm does not activate
Description
Alarm does not operate when alarm operating condition is satisfied.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE
(OPERATING CONDITIONS)”
befo ...
Other materials:
Shift lock system
Component Function Check
1.CHECK SHIFT LOCK OPERATION (PART 1)
1. Turn ignition switch ON.
2. Shift the selector lever to “P” position.
3. Attempt to shift the selector lever to any other than position with the brake
pedal released.
Can the selector lever be shifted to any other positio ...
P0100 MAF sensor
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF.
2. Check ground connection E38. Refer to Ground inspection in GI-44, "Circuit
Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or ...
Positive crankcase ventilation
Inspection
1.CHECK PCV VALVE
With engine running at idle, remove PCV valve from rocker cover. A
properly working valve makes a hissing noise as air passes through
it. A strong vacuum should be felt immediately when a finger is
placed over valve inlet.
Is the inspection result normal?
YES &g ...
