Nissan Juke Service and Repair Manual : Unexpected brake pedal reaction

Description

A malfunction of brake pedal feel (height or others) is detected when brake pedal is depressed.

Diagnosis Procedure

1.CHECK FRONT AND REAR AXLE

Check that there is no excessive looseness in front and rear axle.

• Front axle
- MR16DDT: Refer to FAX-9, "Inspection".

- HR16DE: Refer to FAX-41, "Inspection".

- K9K: Refer to FAX-66, "Inspection".

• Rear axle
- 2WD: Refer to RAX-4, "Inspection".

- 4WD: Refer to RAX-12, "Inspection".

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace error-detected parts.

2.CHECK DISC ROTOR

Check disc rotor runout.

• Front
- LHD: Refer to BR-16, "DISC ROTOR : Inspection and Adjustment".

- RHD: Refer to BR-84, "DISC ROTOR : Inspection and Adjustment".

• Rear
- LHD: Refer to BR-18, "DISC ROTOR : Inspection and Adjustment".

- RHD: Refer to BR-86, "DISC ROTOR : Inspection and Adjustment".

Is the inspection result normal? YES >> GO TO 3.

NO >> Refinish disc rotor.

• Front
- LHD: Refer to BR-16, "DISC ROTOR : Inspection and Adjustment".

- RHD: Refer to BR-84, "DISC ROTOR : Inspection and Adjustment".

• Rear
- LHD: Refer to BR-18, "DISC ROTOR : Inspection and Adjustment".

- RHD: Refer to BR-86, "DISC ROTOR : Inspection and Adjustment".

3.CHECK BRAKE FLUID LEACKAGE

Check fluid leakage.

• Front
- LHD: Refer to BR-30, "FRONT : Inspection".

- RHD: Refer to BR-97, "FRONT : Inspection".

• Rear
- LHD: Refer to BR-39, "REAR : Inspection".

- RHD: Refer to BR-105, "REAR : Inspection".

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace error-detected parts.

4.CHECK BRAKE PEDAL

Check each item of brake pedal.

• LHD: Refer to BR-9, "Inspection and Adjustment".

• RHD: Refer to BR-77, "Inspection and Adjustment".

Is the inspection result normal? YES >> GO TO 5.

NO >> Adjust each item of brake pedal.

• LHD: Refer to BR-9, "Inspection and Adjustment".

• RHD: Refer to BR-77, "Inspection and Adjustment".

5.CHECK BRAKING FORCE

Check brake force using a brake tester.

Is the inspection result normal? YES >> GO TO 6.

NO >> Check each components of brake system.

6.CHECK BRAKE PERFORMANCE

Disconnect ABS actuator and electric unit (control unit) connector so that ABS does not operate. Check that brake force is normal in this condition. Connect harness connectors after checking.

Is the inspection result normal? YES >> Normal

NO >> Check each components of brake system.

    Excessive operation frequency
    Description ESP function, TCS function, ABS function, EBD function and brake limited slip differential (BLSD) function operates in excessive operation frequency. Diagnosis Procedure 1.CHECK BRAK ...

    The braking distance is long
    Description Brake stopping distance is long when ABS function is operated. Diagnosis Procedure CAUTION: Brake stopping distance on slippery road like rough road, gravel road or snowy road may be ...

    Other materials:

    Side air bag (satellite) sensor
    Exploded View 1. Satellite sensor : Vehicle front : Do not reuse : N·m (kg-m, ft-lb) Removal and Installation WARNING: • Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or more. • Never use the air tools or electric tools for serv ...

    LAN System can system (type 6)
    DTC/CIRCUIT DIAGNOSIS Main line between IPDM-E and DLC circuit Diagnosis Procedure 1.CHECK CONNECTOR 1. Turn the ignition switch OFF. 2. Disconnect the battery cable from the negative terminal. 3. Check the following terminals and connectors for damage, bend and loose connection (connector s ...

    Preparation
    Special Service Tools BASIC INSPECTION STEERING WHEEL Inspection NEUTRAL POSITION STEERING WHEEL 1. Make sure that steering gear assembly, steering column assembly and steering wheel are installed in the correct position. 2. Perform neutral position inspection after wheel alignment. Refer ...