Nissan Juke Service and Repair Manual : P range interlock door lock/unlock function does not operate

Nissan Juke Service and Repair Manual / Door & Lock Type 1 / Symptom diagnosis / P range interlock door lock/unlock function does not operate

Diagnosis Procedure

1.CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”

1. Select “DOOR LOCK” of “BCM” using CONSULT-III.

2. Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.

3. Check “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.

Refer to DLK-41, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (With Super Lock)".

Is the inspection result normal? YES >> GO TO 2.

NO >> Set “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.

2.CHECK “AUTOMATIC DOOR LOCK SELECT” SETTING IN “WORK SUPPORT

”

1. Select “DOOR LOCK” of “BCM” using CONSULT-III.

2. Select “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT” mode.

3. Check “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT”.

Refer to DLK-41, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (With Super Lock)".

Is the inspection result normal? YES >> GO TO 3.

NO >> Set “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT”.

3.CHECK “AUTOMATIC DOOR UNLOCK SELECT” SETTING IN “WORK SUPPORT”

1. Select “DOOR LOCK” of “BCM” using CONSULT-III.

2. Select “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT” mode.

3. Check “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.

Refer to DLK-41, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (With Super Lock)".

Is the inspection result normal? YES >> GO TO 4.

NO >> Set “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.

4.REPLACE BCM

1. Replace BCM. Refer to BCS-93, "Removal and Installation".

2. Confirm the operation after replacement.

Is the result normal? YES >> INSPECTION END

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

    IGN off interlock door unlock function does not operate
    Diagnosis Procedure 1.CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT” 1. Select “DOOR LOCK” of “BCM” using CONSULT-III. 2. Select “AUTOMATIC LOCK/UNLOCK SELECT” i ...

    Hazard and buzzer reminder does not operate
    Diagnosis Procedure 1.CHECK DTC WITH BCM AND COMBINATION METER Check that DTC is not detected with BCM and combination meter. Is the inspection result normal? YES >> GO TO 2. NO-1 >& ...

    Other materials:

    Oil pressure switch signal circuit
    Component Function Check 1.CHECK COMBINATION METER INPUT SIGNAL Select the “Data Monitor” for the “METER/M&A” and check the “OIL W/L” monitor value. “OIL W/L” Ignition switch ON : On Engine running : Off >> INSPECTION END Diagnosis Procedure 1.CHECK OIL PRESSURE S ...

    Blower motor
    Diagnosis Procedure 1.CHECK SYMPTOM Check symptom (A or B). Which symptom is detected? A >> GO TO 2. B >> GO TO 7. 2.CHECK FUSE 1. Turn ignition switch OFF. 2. Check 15A fuses (Nos. 14 and 16, located in fuse block (J/B)]. NOTE: Refer to PG-22, "Fuse, Connector and ...

    Refrigerant
    Description CONNECTION OF SERVICE TOOLS AND EQUIPMENT 1. Shut-off valve 2. A/C service valve 3. Recovery/recycling/recharging equipment 4. Vacuum pump 5. Manifold gauge set 6. Refrigerant container (HFC-134a) 7. Weight scale A. Preferred (best) method B. Alternative method C. For ...