Nissan Juke Service and Repair Manual : P position warning does not operate

Diagnosis Procedure

1.CHECK DTC WITH BCM, TCM AND COMBINATION METER

Check that DTC is not detected with BCM, TCM and combination meter.

Is the inspection result normal? YES >> GO TO 2.

NO-1 >> Refer to BCS-67, "DTC Index". (BCM) NO-2 >> Refer to TM-171, "DTC Index" (RE0F10B models) or TM-366, "DTC Index" (RE0F11A models).

(TCM)
NO-3 >> Refer to MWI-36, "DTC Index". (Combination meter)

2.CHECK COMBINATION METER BUZZER

Check combination meter buzzer.

Refer to WCS-40, "Component Function Check".

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace the malfunctioning parts.

3.CHECK INTELLIGENT KEY WARNING BUZZER

Check Intelligent Key warning buzzer.

Refer to DLK-92, "Component Function Check".

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace the malfunctioning parts.

4.CHECK DOOR SWITCH

Check front door switch (driver side).

Refer to DLK-87, "Component Function Check".

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace the malfunctioning parts.

5.CHECK INSIDE KEY ANTENNA

Check inside key antenna.

• Instrument center: Refer to DLK-55, "DTC Logic".

• Console: Refer to DLK-57, "DTC Logic".

• Luggage room: Refer to DLK-59, "DTC Logic".

Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace the malfunctioning parts.

6.CHECK KEY WARNING LAMP

Check key warning lamp.

Refer to DLK-94, "Component Function Check".

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace the malfunctioning parts.

7.REPLACE BCM

1. Replace BCM. Refer to BCS-93, "Removal and Installation".

2. Confirm the operation after replacement.

Is the result normal? YES >> INSPECTION END

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

    Off position warning does not operate
    Diagnosis Procedure 1.CHECK DTC WITH BCM AND COMBINATION METER Check that DTC is not detected with BCM and combination meter. Is the inspection result normal? YES >> GO TO 2. NO-1 >& ...

    ACC warning does not operate
    Diagnosis Procedure 1.CHECK COMBINATION METER BUZZER Check combination meter buzzer. Refer to WCS-40, "Component Function Check". Is the inspection result normal? YES >> GO TO ...

    Other materials:

    Information display (speed limiter)
    Component Function Check 1.CHECK INFORMATION DISPLAY (SPEED LIMITER) FUNCTION 1. Start engine. 2. Press speed limiter MAIN switch. 3. Drive the vehicle at more than 30 km/h (20 MPH). CAUTION: Always drive vehicle at a safe speed. 4. Press SET/COAST switch. 5. Perform a test drive on a flat ...

    B26F5 steering lock status switch
    DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B26F5 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to BCS-83, "DTC Logic". • If DTC B26F5 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to BCS-84, "D ...

    P0234 TC system
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0234 is displayed with DTC P0237 or P0238, first perform the trouble diagnosis for DTC P0237 or P0238. Refer to EC-260, "DTC Logic". DTC CONFIRMATION PROCEDURE 1.PERFORM COMPONENT FUNCTION CHECK Perform component function check. Refer ...