Nissan Juke Service and Repair Manual : License plate lamp circuit
Without daytime running light system
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
1.CHECK TAIL LAMP (RH) OPERATION
Check that the tail lamp (RH) is turned ON.
Is the inspection result normal? YES >> GO TO 2.
NO >> Check tail lamp circuit. Refer to EXL-61, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function Check".
2.CHECK LICENSE PLATE LAMP OPERATION
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the lighting switch, check that the license plate lamp is turned ON.
TAIL : License plate lamp ON Off : License plate lamp OFF
Is the inspection result normal? YES >> License plate lamp circuit is normal.
NO >> Refer to EXL-65, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure".
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure
1.CHECK LICENSE PLATE LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal? YES >> GO TO 2.
NO >> Replace bulb.
2.CHECK LICENSE PLATE LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector and back door opener switch connector.
3. Check continuity between IPDM E/R harness connector and back door opener switch harness connector
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK LICENSE PLATE LAMP GROUND OPEN CIRCUIT
Check continuity between back door opener switch harness connector and ground.
Is the inspection result normal? YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness
With daytime running light system
WITH DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
1.CHECK TAIL LAMP (RH) OPERATION
Check that the tail lamp (RH) is turned ON.
Is the inspection result normal? YES >> GO TO 2.
NO >> Check tail lamp circuit. Refer to EXL-62, "WITH DAYTIME RUNNING LIGHT SYSTEM : Component Function Check".
2.CHECK LICENSE PLATE LAMP OPERATION
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the lighting switch, check that the license plate lamp is turned ON.
TAIL : License plate lamp ON Off : License plate lamp OFF
Is the inspection result normal? YES >> License plate lamp circuit is normal.
NO >> Refer to EXL-66, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure".
WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure
1.CHECK LICENSE PLATE LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal? YES >> GO TO 2.
NO >> Replace bulb.
2.CHECK LICENSE PLATE LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Remove daytime running light relay.
3. Disconnect back door opener switch connector.
4. Check continuity between daytime running light relay harness connector and back door opener switch harness connector.
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK LICENSE PLATE LAMP GROUND OPEN CIRCUIT
Check continuity between back door opener switch harness connector and ground.
Is the inspection result normal? YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.
Tail lamp circuit
Without daytime running light system
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function
1.CHECK TAIL LAMP OPERATION
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active ...
Light & rain sensor
Component Function Check
1.CHECK LIGHT & RAIN SENSOR
1. Clean light & rain sensor detection area of windshield fully.
2. Turn ignition switch ON.
3. Turn lighting switch AUTO.
4. With the ...
Other materials:
Intelligent Around View Monitor
system limitations
WARNING
Listed below are the vital engineering system limitations for the Intelligent Around View Monitor.
Failure to operate your vehicle in strict accordance with these system limitations could blind the driver to surrounding hazards, which could result in ser ...
U1000 can comm circuit
Description
CAN (Controller Area Network) is a serial communication line for real time
applications. It is an on-board multiplex
communication line with high data communication speed and excellent error
detection ability. A modern
vehicle is equipped with many ECUs, and each control unit shar ...
G sensor
Exploded View
1. Bracket
2. G sensor
: Vehicle front
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
Removal and Installation
CAUTION:
• Never drop or strike G sensor, because it has little tolerance for impact.
• Never use a power tool to avoid impact.
REMOVAL
1. Disconnect the battery ...
