Nissan Juke Service and Repair Manual : B26F2 ignition relay

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON under the following conditions, and wait for 2 seconds or more.

CVT models
- Selector lever is in the P or N position - Do not depress brake pedal

M/T models
- Do not depress clutch pedal

2. Check “Self-diagnosis result” with CONSULT-III.

Is DTC detected? YES >> Go to PCS-105, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK IPDM E/R SELF-DIAGNOSTIC RESULT

1. Turn ignition switch ON.

2. Erase the DTC of IPDM E/R.

3. Turn ignition switch OFF.

4. Turn ignition switch ON and check the DTC again.

Is DTC detected? YES >> Repair or replace the malfunctioning part. Refer to PCS-25, "DTC Index".

NO >> GO TO 2.

2.CHECK IGNITION RELAY (IPDM E/R) CONTROL SIGNAL

1. Turn ignition switch OFF.

2. Check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace IPDM E/R.

NO >> GO TO 3.

3.CHECK IGNITION RELAY (IPDM E/R) CONTROL SIGNAL CIRCUIT - 1

1. Turn ignition switch OFF.

2. Disconnect BCM and IPDM E/R connectors.

3. Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace harness.

4.CHECK IGNITION RELAY (IPDM E/R) CONTROL SIGNAL CIRCUIT - 2

1. Connect IPDM E/R connectors.

2. Check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace BCM. Refer to BCS-93, "Removal and Installation".

NO >> Replace IPDM E/R.

    B26F1 ignition relay
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE 1. Turn ignition switch ON under the following conditions, and wait for 2 seconds or more. CVT ...

    B26F6 BCM
    DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B26F6 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to BCS-83, "DTC Logic". • If DTC B26F6 is disp ...

    Other materials:

    Upper link
    Exploded View 1. Rear suspension member 2. Adjusting bolt 3. Upper link 4. Eccentric disk 5. Lower link 6. Suspension arm bracket 7. Suspension arm : Vehicle front : Always replace after every disassembly. : N·m (kg-m, ft-lb) Removal and Installation REMOVAL 1. Remove tires. WT- ...

    Basic inspection
    DIAGNOSIS AND REPAIR WORKFLOW Work Flow OVERALL SEQUENCE DETAILED FLOW 1.INTERVIEW FOR MALFUNCTION Interview the symptom to the customer. >> GO TO 2. 2.SYMPTOM CHECK Check the symptom from the customer's information. >> GO TO 3. 3.BASIC INSPECTION Check the operation o ...

    B1001, B1002, B1003, B1004, B1005 diagnosis sensor unit
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III. Without CONSULT-III 1. Turn ignition switch ON. 2. Check the air bag warning lamp statu ...