Nissan Juke Service and Repair Manual : Super lock does not operatE

All door

ALL DOOR : Diagnosis Procedure

1.CHECK SUPER LOCK ACTUATOR

Check front driver side super lock actuator.

Refer to DLK-407, "DRIVER SIDE : Component Function Check".

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace the malfunctioning parts.

2.CONFIRM THE OPERATION

1. Replace BCM. Refer to BCS-93, "Removal and Installation".

2. Confirm the operation after replacement.

Is the result normal? YES >> INSPECTION END

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

Driver side

DRIVER SIDE : Diagnosis Procedure

1.CHECK SUPER LOCK ACTUATOR

Check front driver side super lock actuator.

Refer to DLK-407, "DRIVER SIDE : Component Function Check".

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace the malfunctioning parts.

2.CONFIRM THE OPERATION

1. Replace BCM. Refer to BCS-93, "Removal and Installation".

2. Confirm the operation after replacement.

Is the result normal? YES >> INSPECTION END

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

Passenger side

PASSENGER SIDE : Diagnosis Procedure

1.CHECK SUPER LOCK ACTUATOR

Check front passenger side super lock actuator.

Refer to DLK-408, "PASSENGER SIDE : Component Function Check".

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace the malfunctioning parts.

2.CONFIRM THE OPERATION

1. Replace BCM. Refer to BCS-93, "Removal and Installation".

2. Confirm the operation after replacement.

Is the result normal? YES >> INSPECTION END

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

Rear LH

REAR LH : Diagnosis Procedure

1.CHECK SUPER LOCK ACTUATOR

Check super lock actuator rear LH.

Refer to DLK-409, "REAR LH : Component Function Check".

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace the malfunctioning parts.

2.CONFIRM THE OPERATION

1. Replace BCM. Refer to BCS-93, "Removal and Installation".

2. Confirm the operation after replacement.

Is the result normal? YES >> INSPECTION END

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

Rear RH

REAR RH : Diagnosis Procedure

1.CHECK SUPER LOCK ACTUATOR

Check super lock actuator rear RH.

Refer to DLK-410, "REAR RH : Component Function Check".

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace the malfunctioning parts.

2.CONFIRM THE OPERATION

1. Replace BCM. Refer to BCS-93, "Removal and Installation".

2. Confirm the operation after replacement.

Is the result normal? YES >> INSPECTION END

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

    Door lock status indicator does not illuminate
    Diagnosis Procedure 1.CHECK DOOR LOCK STATUS INDICATOR Check door lock status indicator. Refer to DLK-395, "Component Function Check". Is the inspection result normal? YES >> ...

    Back door does not opened
    Diagnosis Procedure 1.CHECK BACK DOOR OPENER SWITCH Check back door opener switch. Refer to DLK-384, "Component Function Check". Is the inspection result normal? YES >> GO TO ...

    Other materials:

    P159B G sensor
    For M/T models : DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test. 1. Turn ignition switch OFF and wait at least 10 seconds. 2. T ...

    Camshaft
    Exploded View 1. Camshaft position sensor (PHASE) 2. O-ring 3. Camshaft bracket 4. Camshaft (EXH) 5. Camshaft sprocket (EXH) 6. Camshaft sprocket (INT) 7. Camshaft (INT) 8. Valve lifter (EXH) 9. Valve lifter (INT) 10. Signal plate (INT) 11 Signal plate (EXH) A.Tightening must be ...

    B2614 ACC relay circuit
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE 1. Turn the power supply position to ACC under the following conditions, and wait for 2 second or more. CVT models - Selector lever is in the P or N position - Do not depress brake pedal M/T m ...