Nissan Juke Service and Repair Manual : Service data and specifications (SDS)

Nissan Juke Service and Repair Manual / Maintenance / Service data and specifications (SDS)

DRIVE BELT (MR16DDT)

DRIVE BELT (MR16DDT) : Drive Belt

DRIVE BELT

DRIVE BELT (HR16DE)


DRIVE BELT (HR16DE)

DRIVE BELT (HR16DE) : Drive Belt

DRIVE BELT

Belt Deflection

*: When engine is cold.


*: When engine is cold.

Belt Tension and Frequency

*: When engine is cold.


*: When engine is cold.

DRIVE BELT (K9K)

DRIVE BELT (K9K) : Drive Belt

DRIVE BELT

ENGINE COOLANT (MR16DDT)


ENGINE COOLANT (MR16DDT)

ENGINE COOLANT (MR16DDT) : Periodical Maintenance Specification

ENGINE COOLANT CAPACITY (APPROXIMATE)

ENGINE COOLANT (HR16DE)


ENGINE COOLANT (HR16DE)

ENGINE COOLANT (HR16DE) : Periodical Maintenance Specification

ENGINE COOLANT CAPACITY (APPROXIMATE)

ENGINE COOLANT (K9K)


ENGINE COOLANT (K9K)

ENGINE COOLANT (K9K) : Periodical Maintenance Specification

ENGINE COOLANT CAPACITY (APPROXIMATE)

ENGINE OIL (MR16DDT)


ENGINE OIL (MR16DDT)

ENGINE OIL (MR16DDT) : Periodical Maintenance Specification

ENGINE OIL CAPACITY (APPROXIMATE)

ENGINE OIL (HR16DE)


ENGINE OIL (HR16DE)

ENGINE OIL (HR16DE) : Periodical Maintenance Specification

ENGINE OIL CAPACITY (APPROXIMATE)

ENGINE OIL (K9K)


ENGINE OIL (K9K) ENGINE OIL (K9K) : Standard and Limit

OIL PRESSURE

OIL CAPACITY (APPROXIMATE)


OIL CAPACITY (APPROXIMATE)

TIGHTENING TORQUE


TIGHTENING TORQUE

SPARK PLUG (MR16DDT)


SPARK PLUG (MR16DDT)

SPARK PLUG (MR16DDT) : Spark Plug

SPARK PLUG

SPARK PLUG (HR16DE)


SPARK PLUG (HR16DE)

SPARK PLUG (HR16DE) : Spark Plug

SPARK PLUG (PLATINUM-TIPPED TYPE)

ROAD WHEEL


ROAD WHEEL

ROAD WHEEL : Road Wheel

ALUMINUM WHEEL

STEEL WHEEL


STEEL WHEEL

STEEL WHEEL (EMERGENCY)


STEEL WHEEL (EMERGENCY)


    Body maintenance
    Locks, hinges and hood latch LOCKS, HINGES AND HOOD LATCH : Lubr Seat belt, buckles, retractors, anchors and adjusters SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS : Inspection For fron ...

    Other materials:

    C1176 stop lamp SW2
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test. >> GO TO 2. 2.CHECK DTC DETECTION With CONSULT ...

    Draining
    1. Run the vehicle to warm up the transfer unit sufficiently. 2. Stop the engine and remove the drain plug (1) and gascket to drain the transfer oil. 3. Before installing drain plug, set a new gasket. Install drain plug on the transfer and tighten to the specified torque. Refer to DLN- 113, &qu ...

    B2196 dongle unit
    Description BCM performs ID verification between BCM and dongle unit. When verification result is OK, BCM permits cranking. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE 1. Turn ignition switch ON. 2. Turn ignition switch OFF. 3. Turn igni ...