Nissan Juke Service and Repair Manual : Rear window defogger on signal

With auto A/C

WITH AUTO A/C : Description

Turns the indicator lamp in the rear window defogger switch ON when operating the rear window defogger

WITH AUTO A/C : Component Function Check

1.CHECK REAR WINDOW DEFOGGER ON SIGNAL

Check that the indicator lamp of rear window defogger switch is illuminated when turning the rear window defogger switch ON.

Is the inspection result normal? OK >> Rear window defogger ON signal is OK.

NG >> Refer to DEF-37, "WITH AUTO A/C : Diagnosis Procedure".

WITH AUTO A/C : Diagnosis Procedure

1.CHECK REAR WINDOW DEFOGGER INDICATOR LAMP ON SIGNAL

1. Turn ignition switch OFF.

2. Disconnect multi display unit connector.

3. Turn ignition switch ON.

4. Check voltage between multi display unit harness connector ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace multi display unit Refer to HAC-91, "Removal and Installation" (4WD models) or HAC- 188, "Removal and Installation" (2WD models).

NO >> Repair or replace harness.

Without auto A/C

WITHOUT AUTO A/C : Description

Turns the indicator lamp in the rear window defogger switch ON when operating the rear window defogger.

WITHOUT AUTO A/C : Component Function Check

1.CHECK REAR WINDOW DEFOGGER ON SIGNAL

Check that the indicator lamp of rear window defogger switch is illuminated when turning the rear window defogger switch ON.

Is the inspection result normal? OK >> Rear window defogger ON signal is OK.

NG >> Refer to DEF-37, "WITHOUT AUTO A/C : Diagnosis Procedure".

WITHOUT AUTO A/C : Diagnosis Procedure

1.CHECK REAR WINDOW DEFOGGER INDICATOR LAMP ON SIGNAL

1. Turn ignition switch OFF.

2. Disconnect A/C control connector.

3. Turn ignition switch ON.

4. Check voltage between A/C control harness connector ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace A/C control. Refer to HAC-239, "Removal and Installation" (4WD models) or HAC-304, "Removal and Installation".

NO >> Repair or replace harness.

Without A/C

WITHOUT A/C : Description

Turns the indicator lamp in the rear window defogger switch ON when operating the rear window defogger.

WITHOUT A/C : Component Function Check

1.CHECK REAR WINDOW DEFOGGER ON SIGNAL

Check that the indicator lamp of rear window defogger switch is illuminated when turning the rear window defogger switch ON.

Is the inspection result normal? OK >> Rear window defogger ON signal is OK.

NG >> Refer to DEF-38, "WITHOUT A/C : Diagnosis Procedure".

WITHOUT A/C : Diagnosis Procedure

1.CHECK REAR WINDOW DEFOGGER INDICATOR LAMP ON SIGNAL

1. Turn ignition switch OFF.

2. Disconnect heater control connector.

3. Turn ignition switch ON.

4. Check voltage between heater control harness connector ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace heater control. Refer to HAC-331, "Removal and Installation".

NO >> Repair or replace harness.

    Passenger side door mirror defogger
    Description Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror from fogging up. Component Function Check 1.CHECK PASSENGER SIDE DOOR MIRR ...

    Rear window defogger system
    Wiring Diagram - DEFOGGER CONTROL SYSTEM - For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not described in wiring diagram), refer to GI-12, " ...

    Other materials:

    Diagnosis system (IPDM E/R)
    With intelligent key WITH INTELLIGENT KEY : Diagnosis Description AUTO ACTIVE TEST Description In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation. • Oil pressure warning lamp (only for K9K engine models) • Rear window defogger • F ...

    P1813 4WD mode switch
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test. >> GO TO 2. 2.DTC REPRODUCTION PROCEDURE With ...

    Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
    NOTE: • Before removing and installing any control units, first turn the ignition switch to the LOCK position, then disconnect both battery cables. • After finishing work, confirm that all control unit connectors are connected properly, then re-connect both battery cables. • Always use CONS ...