Nissan Juke Service and Repair Manual : P position warning does not operate

Diagnosis Procedure

1.CHECK DTC WITH BCM, TCM AND COMBINATION METER

Check that DTC is not detected with BCM, TCM and combination meter.

Is the inspection result normal? YES >> GO TO 2.

NO-1 >> Refer to BCS-67, "DTC Index". (BCM) NO-2 >> Refer to TM-171, "DTC Index" (RE0F10B models) or TM-366, "DTC Index" (RE0F11A models).

(TCM)
NO-3 >> Refer to MWI-36, "DTC Index". (Combination meter)

2.CHECK COMBINATION METER BUZZER

Check combination meter buzzer.

Refer to WCS-40, "Component Function Check".

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace the malfunctioning parts.

3.CHECK INTELLIGENT KEY WARNING BUZZER

Check Intelligent Key warning buzzer.

Refer to DLK-263, "Component Function Check".

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace the malfunctioning parts.

4.CHECK DOOR SWITCH

Check front door switch (driver side).

Refer to DLK-258, "Component Function Check".

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace the malfunctioning parts.

5.CHECK INSIDE KEY ANTENNA

Check inside key antenna.

• Instrument center: Refer to DLK-230, "DTC Logic".

• Console: Refer to DLK-232, "DTC Logic".

• Luggage room: Refer to DLK-234, "DTC Logic".

Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace the malfunctioning parts.

6.CHECK KEY WARNING LAMP

Check key warning lamp.

Refer to DLK-265, "Component Function Check".

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace the malfunctioning parts.

7.REPLACE BCM

1. Replace BCM. Refer to BCS-93, "Removal and Installation".

2. Confirm the operation after replacement.

Is the result normal? YES >> INSPECTION END

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

    Off position warning does not operate
    Diagnosis Procedure 1.CHECK DTC WITH BCM AND COMBINATION METER Check that DTC is not detected with BCM and combination meter. Is the inspection result normal? YES >> GO TO 2. NO-1 >& ...

    ACC warning does not operate
    Diagnosis Procedure 1.CHECK COMBINATION METER BUZZER Check combination meter buzzer. Refer to WCS-40, "Component Function Check". Is the inspection result normal? YES >> GO TO ...

    Other materials:

    Clutch disc and clutch cover
    Except for K9K : Exploded View HR16DE 1. Flywheel 2. Clutch disc 3. Clutch cover 4. Input shaft A. First step B. Final step : N·m (kg-m, ft-lb) : Apply lithium-based grease including molybdenum disulphide. MR16DDT 1. Flywheel 2. Clutch disc 3. Clutch cover 4. Input shaft A. ...

    B2098 ignition relay on stuck
    Description The ignition relay integrated in IPDM E/R is operated with ignition switch ON signal from the ignition switch. DTC Logic DTC DETECTION LOGIC 1.PERFORM DTC CONFIRMATION PROCEDURE 1. Turn ignition switch ON. 2. Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSUL ...

    B2014 chain of STRG-IMMU
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE 1. Lock steering. NOTE: 3. Press the push-button ignition switch. 4. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT-III. Is DTC detected? YES >> Go to SEC-70, " ...