Nissan Juke Service and Repair Manual : Hood lock

Exploded View

1. Hood lock control cable assembly


1. Hood lock control cable assembly 2. Hood lock assembly

: Clip
: N·m (kg-m, ft-lb)
: Body grease

Hood lock

HOOD LOCK : Removal and Installation

REMOVAL

1. Remove front center grille. Refer to EXT-18, "Removal and Installation".

2. Remove crash zone sensor. Refer to SR-26, "Removal and Installation".

3. Remove hood lock assembly mounting bolts, and then remove hood lock assembly.

4. Disconnect hood lock control cable assembly (2) from hood lock assembly (1).

INSTALLATION


INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:
• Check that hood lock control cable is properly engaged with hood lock.

• After installation, perform hood fitting adjustment. Refer to DLK-556, "HOOD ASSEMBLY : Adjustment".

• After installation, perform hood lock control inspection. Refer to DLK-587, "Inspection".

Hood lock control cable

HOOD LOCK CONTROL CABLE : Removal and Installation

REMOVAL

1. Disconnect hood lock control cable assembly from hood lock assembly.

2. Remove fender protector (LH). Refer to EXT-22, "Removal and Installation".

3. Remove hood lock cable clip.

4. Remove hood lock control cable assembly of instrument lower panel (LH), and then remove fuel filler lid opener cable (2) from fuel filler lid opener lever (1).

5. Remove grommet on the lower dash, and pull the hood lock control cable


5. Remove grommet on the lower dash, and pull the hood lock control cable toward the passenger compartment.

CAUTION:
While pulling, never to damage (peeling) the outside of hood lock control cable.

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:
• Never to bend cable too much, keeping the radius 100 mm (3.937 in) or more.

• Check that cable is not offset from the positioning grommet, and apply the sealant to the grommet (at * mark) properly.

• Check that hood lock control cable is properly engaged with hood lock.


• Check that hood lock control cable is properly engaged with hood lock.

• After installation, perform hood fitting adjustment. Refer to DLK-556, "HOOD ASSEMBLY : Adjustment".

• After installation, perform hood lock control inspection. Refer to DLK-587, "Inspection".

Inspection

NOTE

:
If the hood lock cable is bent or deformed, replace it.

1. Check that secondary latch is securely engaged with securely striker from the dead load of the hood assembly.

2. Check that primary latch is securely engaged with primary striker when hood assembly is closed [free-fall from approximately 200 mm (7.874 in) height].

CAUTION:
Never free-fall hood assembly from a height of 300 (11.811 in) mm or more.

3. While operating the hood opener carefully, check that the front end of the hood is lifted by approximately 20 mm (0.787 in) (A). Also, check that the hood opener returns to the original position.

1. Primary striker


1. Primary striker
2. Primary latch
3. Secondary latch
4. Secondary striker

4. Check that secondary latch is properly engaged with secondary striker [6.8 mm (0.268 in)] (B).

5. Check the hood lock lubrication condition. If necessary, apply body grease to hood lock.

: Grease up point


Front door lock


    Back door
    Exploded View REMOVAL 1. Back door weather-strip 2. Back door stay 3. Back door stay lower bracket 4. Bumper rubber 5. Back door striker 6. Back door panel 7. Back door hinge 8. Hole c ...

    Front door lock
    Exploded View 1. Door key cylinder assembly (driver side) Outside handle escutcheon (passenger side) 2. Rear gasket 3. Outside handle bracket 4. TORX bolt 5. Key rod (driver side) 6. Doo ...

    Other materials:

    Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
    NOTE: • Before removing and installing any control units, first turn the ignition switch to the LOCK position, then disconnect both battery cables. • After finishing work, confirm that all control unit connectors are connected properly, then re-connect both battery cables. • Always use CONS ...

    High-mounted stop lamp
    Exploded View 1. High-mounted stop lamp 2. Seal packing : N·m (kg-m, in-lb) Removal and Installation CAUTION: Disconnect battery negative terminal or remove the fuse. REMOVAL 1. Remove blind seal from back door inside. CAUTION: Be careful not to damage the blind seal, so that it can b ...

    Eco information
    CAUTION Do not adjust the display controls while driving so that full attention may given to vehicle operation. The following ECO INFO mode will appear on the display by pushing the ECO information button, then turning the selection dial to scroll through the different screens. While driving, ...