Nissan Juke Service and Repair Manual : Back door request switch

Component Function Check

1.CHECK FUNCTION

1. Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.

2. Select “REQ SW-BD/TR” in “DATA MONITOR” mode.

3. Check that the function operates normally according to the following conditions.

Is the inspection result normal?


Is the inspection result normal? YES >> Back door request switch is OK.

NO >> Refer to DLK-246, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK BACK DOOR REQUEST SWITCH INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect back door opener switch connector.

3. Check voltage between back door opener switch harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK BACK DOOR REQUEST SWITCH CIRCUIT

1. Disconnect BCM connector.

2. Check continuity between BCM harness connector and back door opener switch harness connector.

3. Check continuity between BCM harness connector and ground.


3. Check continuity between BCM harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace BCM. Refer to BCS-93, "Removal and Installation".

NO >> Repair harness or connector.

3.CHECK BACK DOOR REQUEST SWITCH GROUND CIRCUIT

Check continuity between back door opener switch harness connector and ground.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace harness.

4.CHECK BACK DOOR REQUEST SWITCH

Refer to DLK-247, "Component Inspection".

Is the inspection result normal? YES >> GO TO 5.

NO >> Replace back door opener switch.

5.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident".

>> INSPECTION END

Component Inspection

1.CHECK BACK DOOR REQUEST SWITCH

1. Turn ignition switch OFF.

2. Disconnect back door opener switch connector.

3. Check continuity between back door opener switch terminals.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace back door opener switch.

    Back door opener switch
    Component Function Check 1.CHECK FUNCTION 1. Select “TRUNK” of “BCM” using CONSULT-III. 2. Select “TR/BD OPEN SW” in “DATA MONITOR” mode. 3. Check that the function operates normally according to ...

    Buzzer (combination meter)
    Component Function Check 1.CHECK FUNCTION 1. Select “INTELLIGENT KEY” of “BCM” using CONSULT-III. 2. Select “INSIDE BUZZER” in “ACTIVE TEST” mode. 3. Check that the function operates normally acco ...

    Other materials:

    Wheel sensor
    Front wheel sensor : Exploded View 1. Front LH wheel sensor 2. Front LH wheel sensor harness connector : Vehicle front : N·m (kg-m, in-lb) NOTE: Front RH wheel sensor is symmetrically opposite of LH. Front wheel sensor : Removal and Installat REMOVAL 1. Remove tires. 2. Remove the fende ...

    B2578, B2579 In-vehicle sensor
    DTC Logic DTC DETECTION LOGIC NOTE: • If DTC is displayed along with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to HAC- 141, "DTC Logic". • If DTC is displayed along with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to HAC- 142, &qu ...

    IGN off interlock door unlock function does not operate
    Diagnosis Procedure 1.CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT” 1. Select “DOOR LOCK” of “BCM” using CONSULT-III. 2. Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode. 3. Check “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”. Refer to DLK-41, "DOOR LOCK : ...