Nissan Juke Service and Repair Manual : B1215, B1216, B1217 satellite sensor LH

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.CHECK SELF-DIAG RESULT

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

1. Turn ignition switch ON.Without CONSULT-III


1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to SRC-12, "On Board Diagnosis Function".

NOTE

:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected? YES >> Refer to SRC-144, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Proce

WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) • Never use unspecified tester or other measuring device.

1.CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal? YES >> GO TO 2.

NO >> Replace harness connector.

2.CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal? YES >> GO TO 3.

NO >> Replace wiring harness.

3.REPLACE SATELLITE SENSOR

1. Replace satellite sensor LH. Refer to SR-28, "Removal and Installation".

2. Perform DTC confirmation procedure. Refer to SRC-144, "DTC Logic" Is DTC detected? YES >> GO TO 4.

NO >> INSPECTION END

4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace air bag diagnosis sensor unit. Refer to SR-30, "Removal and Installation".

2. Perform DTC confirmation procedure. Refer to SRC-144, "DTC Logic".

Is DTC detected? YES >> GO TO 1.

NO >> INSPECTION END

    B1212, B1213, B1214 satellite sensor RH
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSU ...

    B1218, B1219, B1220, B1221, B1222, B1223 diagnosis sensor unit
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSU ...

    Other materials:

    Refrigerant pressure sensor
    Component Function Check 1.CHECK REFRIGERANT PRESSURE SENSOR OVERALL FUNCTION 1. Start engine and warm it up to normal operating temperature. 2. Turn A/C switch and blower fan switch ON. 3. Check the voltage between ECM harness connector and ground. Is the inspection result normal? YES >& ...

    Headlamp washer nozzle and tube
    Exploded View 1. Washer tank 2. Headlamp washer tube (tank side) 3. Headlamp washer tube RH 4. Headlamp washer nozzle connector RH 5. Headlamp washer nozzle bracket RH 6. Headlamp washer nozzle RH 7. Headlamp washer nozzle joint 8. Headlamp washer nozzle bracket LH 9. Headlamp washe ...

    P0120 TP sensor
    DTC Logic DTC DETECTION LOGIC Diagnosis Procedure 1.CHECK GROUND CONNECTIONS 1. Turn ignition switch OFF and wait at least 20 seconds. 2. Check ground connection E38. Refer to Ground inspection in GI-44, "Circuit Inspection". Is the inspection result normal? YES >> GO TO ...