Nissan Juke Service and Repair Manual : B1145 curtain air bag module RH

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.CHECK SELF-DIAG RESULT

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

1. Turn ignition switch ON.Without CONSULT-III


1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to SRC-12, "On Board Diagnosis Function".

NOTE

:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected? YES >> Refer to SRC-112, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) • Never use unspecified tester or other measuring device.

1.CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal? YES >> GO TO 2.

NO >> Replace harness connector.

2.CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal? YES >> GO TO 3.

NO >> Replace wiring harness.

3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace air bag diagnosis sensor unit. Refer to SR-30, "Removal and Installation".

2. Perform DTC confirmation procedure. Refer to SRC-112, "DTC Logic".

Is DTC detected? YES >> GO TO 4.

NO >> INSPECTION END

4.REPLACE CURTAIN AIR BAG MODULE

1. Replace curtain air bag module RH. Refer to SR-24, "Removal and Installation".

2. Perform DTC confirmation procedure. Refer to SRC-112, "DTC Logic".

Is DTC detected?

YES >> GO TO 1.

NO >> INSPECTION END

    B1144 diagnosis sensor unit
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSU ...

    B1146 curtain air bag module RH
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSU ...

    Other materials:

    Injection tube and fuel injector
    Exploded View 1. Spill hose 2. Injection tube 3. Fuel injector 4. Heat protection washer 5. Fuel injector bracket 6. Fuel injector bracket spacer 7. Fuel rail stud bolt 8. Fuel rail 9. High pressure protection cover (lower) 10. Injection tube 11. High pressure supply pump 12. H ...

    Power supply and ground circuit
    A/C auto AMP. : Diagnosis Procedure 1.CHECK SYMPTOM Check symptom (A or B). Which symptom is detected? A >> GO TO 2. B >> GO TO 5. 2.CHECK FUSE 1. Turn ignition switch OFF. 2. Check 10A fuse (No. 3). NOTE: Refer to PG-23, "Fuse and Fusible Link Arrangement". ...

    Rear oil seal
    REAR OIL SEAL : Removal and Installation REMOVAL 1. Remove transaxle assembly. Refer to TM-301, "Exploded View" (CVT models) or TM-84, "MR16DDT : Exploded View" (M/T models). 2. Remove clutch cover and clutch disk (M/T models). Refer to CL-29, "EXCEPT FOR K9K : Explo ...