Nissan Juke Service and Repair Manual : Additional service when replacing control unit

ECM

ECM : Description

Performing the following procedure can automatically activate recommunication of ECM and BCM, but only when the ECM is replaced with a new one*.

*: New one means a virgin ECM that has never been energized on-board.

(In this step, initialization procedure by CONSULT-III is not necessary) NOTE

:
• When registering new Key IDs or replacing the ECM that is not brand new, refer to CONSULT-III Operation Manual NATS-IVIS/NVIS.

• If multiple keys are attached to the key holder, separate them before beginning work.

• Distinguish keys with unregistered key IDs from those with registered IDs.

ECM : Work Procedure

1.PERFORM ECM RECOMMUNICATING FUNCTION

1. Install ECM.

2. Insert the registered ignition key* into key cylinder, then turn ignition switch ON.

*: To perform this step, use the key that is used before performing ECM replacement.

3. Maintain ignition switch in the ON position for at least 5 seconds.

4. Turn ignition switch OFF.

5. Start the engine.

>> GO TO 2.

2.PERFORM ADDITIONAL SERVICE WHEN REPLACING ECM

Perform the following procedure.

• MR16DDT: EC-133, "Work Procedure" • HR16DE: EC-541, "Work Procedure" • K9K: EC-879, "Work Procedure"

>> END

BCM

BCM : Description

BEFORE REPLACEMENT

When replacing BCM, save or print current vehicle specification with CONSULT-III configuration before replacement.

NOTE

:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after replacing BCM.

AFTER REPLACEMENT

CAUTION:
• When replacing BCM, you must perform “WRITE CONFIGURATION” with CONSULT-III.

- Complete the procedure of “WRITE CONFIGURATION” in order.

- If you set incorrect “WRITE CONFIGURATION”, incidents might occur.

- Configuration is different for each vehicle model. Confirm configuration of each vehicle model.

• When replacing BCM, perform the system initialization (NATS).

BCM : Work Procedure

1.SAVING VEHICLE SPECIFICATION

Perform “READ CONFIGURATION” to save or print current vehicle specification.CONSULT-III Configuration


Perform “READ CONFIGURATION” to save or print current vehicle specification. Refer to BCS-151, "Description".

NOTE

:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after replacing BCM.

>> GO TO 2.

2.REPLACE BCM

Replace BCM. Refer to BCS-161, "Removal and Installation".

>> GO TO 3.

3.WRITING VEHICLE SPECIFICATION

Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - ManualCONSULT-III Configuration


Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Manual selection” to write vehicle specification. Refer to BCS-151, "Work Procedure".

>> GO TO 4.

4.INITIALIZE BCM (NATS)

Perform BCM initialization. (NATS) >> WORK END

    Diagnosis and repair work flow
    Work Flow OVERALL SEQUENCE DETAILED FLOW 1.GET INFORMATION ABOUT SYMPTOM Get the detailed information from the customer about the symptom (the condition and the environment when the incident/ ...

    Other materials:

    P1705 TP sensor
    Description Electric throttle control actuator consists of throttle control motor, accelerator pedal position sensor, throttle position sensor etc. The actuator sends a signal to the ECM, and ECM sends the signal to TCM with CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATI ...

    Vehicle information display
    The vehicle information display in your Nissan Leaf is strategically located to the left of the speedometer, serving as the central hub for essential driving data. It provides real-time updates and critical insights to help you optimize your driving experience, including: ...

    Precaution
    Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the ...