Nissan Juke Service and Repair Manual : Emission control not satisfactory

Description

CHART 22: EMISSION CONTROL NOT SATISFACTORY

Diagnosis Procedure

1.CHECK ECM POWER SUPPLY AND GROUND CIRCUIT

Check ECM power supply and ground circuit. Refer to EC-885, "Diagnosis Procedure".

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace harness or connector.

2.CHECK WIRING HARNESS

Visually check the condition of the engine wiring harness.

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace harness or connector.

3.CHECK AIR INTAKE SYSTEM

Check air intake system. Refer to EM-280, "Removal and Installation".

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace air intake system.

4.CHECK ELECTRIC THROTTLE CONTROL ACTUATOR

Check electric throttle control actuator. Refer to EC-909, "Diagnosis Procedure".

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace.

5.CHECK MASS AIR FLOW SENSOR

Check mass air flow sensor. Refer to EC-902, "Component Inspection".

Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace.

6.CHECK TURBOCHARGER

Check that the turbocharger is working properly. Refer to EC-1003, "Diagnosis Procedure".

Is the turbocharger correct? Yes >> GO TO 7.

No >> Repair or replace.

7.CHECK EGR SYSTEM

Check EGR system. Refer to EC-954, "Diagnosis Procedure".

Is the inspection result normal? YES >> GO TO 8.

NO >> Repair or replace.

8.CHECK HIGH PRESSURE SUPPLY PUMP (PRESSURE CONTROL VALVE)

Perform the TEST 3: HIGH PRESSURE SUPPLY PUMP (PRESSURE CONTROL VALVE). Refer to EC-868, "Work Procedure [TEST 3: High Pressure Supply Pump (Pressure Control Valve) Check]".

>> GO TO 9.

9.CHECK HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE)

Perform the TEST 4: HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE). Refer to EC- 869, "Work Procedure [TEST 4: High Pressure Supply Pump (Volumetric Control Valve) Check]".

>> GO TO 10.

10.CHECK RAIL HIGH PRESSURE CONTROL CIRCUIT

Perform the TEST 5: RAIL HIGH PRESSURE CONTROL CIRCUIT CHECK. Refer to EC-871, "Work Procedure (TEST 5: Rail High Pressure Regulation Check)".

>> GO TO 11.

11.CHECK MAJOR LEAK IN FUEL INJECTOR/FUEL INJECTORS OPEN

Perform the TEST 6: MAJOR LEAK IN FUEL INJECTOR/FUEL INJECTORS OPEN. Refer to EC-876, "Work Procedure (TEST 6: Fuel Injectors Leak Check)".

>> GO TO 12.

12.CHECK INCORRECT FUEL INJECTION QUANTITY

Perform the TEST 7: INCORRECT FUEL INJECTION QUANTITY. Refer to EC-877, "Work Procedure (TEST 7: Fuel Injection Quantity Check)".

>> INSPECTION END

    Engine emits white smoke (especially when starting)
    Description CHART 21: ENGINE EMITS WHITE SMOKE (ESPECIALLY WHEN STARTING) Diagnosis Procedure 1.CHECK FUEL Check that the fuel reservoir is correctly filled and with the right fuel. >> GO ...

    Service data and specifications (SDS)
    Idle Speed *: Under the following conditions • A/C switch: OFF • Electric load: OFF (Lights, glow plug, heater fan & rear window defogger) • Steering wheel: Kept in straight-ahead posi ...

    Other materials:

    Intelligent key warning buzzer
    Component Function Check 1.CHECK FUNCTION 1. Select “INTELLIGENT KEY” of “BCM” using CONSULT-III. 2. Select “OUTSIDE BUZZER” in “ACTIVE TEST” mode. 3. Check that the function operates normally according to the following conditions. Is the inspection result normal? YES >& ...

    Rear suspension beam
    Exploded View 1. Rear suspension beam 2. Rear suspension arm bracket : Always replace after every disassembly. : N·m (kg-m, ft-lb) Removal and Installation REMOVAL 1. Remove tires. Refer to WT-7, "Removal and Installation". 2. Drain brake fluid. Refer to BR-12, "Draining ...

    Hood lock
    Exploded View 1. Hood lock control cable assembly 2. Hood lock assembly : Clip : N·m (kg-m, ft-lb) : Body grease Hood lock HOOD LOCK : Removal and Installation REMOVAL 1. Remove front center grille. Refer to EXT-18, "Removal and Installation". 2. Remove crash zone sensor. Ref ...