Nissan Juke Service and Repair Manual : Component parts

Component Parts Location

1. Remote keyless entry receiver


1. Remote keyless entry receiver Refer to DLK-361, "Component Parts Location" (With super lock) or DLK-492, "Component Parts Location" (Without super lock).

2. Combination meter Refer to MWI-4, "METER SYSTEM : Component Parts Location".

3. Stop lamp switch Refer to BRC-9, "Component Parts Location" (Without ESP) or BRC-97, "Component Parts Location" (With ESP).

4. NATS antenna amp. (Behind ignition switch) 5. Ignition switch
6. Transmission range switch Refer to TM-131, "CVT CONTROL SYSTEM : Component Parts Location" (CVT: RE0F10A) or TM-314, "CVT CONTROL SYSTEM : Component Parts Location" (RE0F11A).

7. ECM Refer to EC-25, "ENGINE CONTROL SYSTEM : Component Parts Location" (MR16DDT), EC-455, "ENGINE CONTROL SYSTEM : Component Parts Location" (HR16DE) or EC-813, "Component Parts Location" (K9K).

8. IPDM E/R Refer to PCS-5, "Component Parts Location".

9. TCM Refer to TM-131, "CVT CONTROL SYSTEM : Component Parts Location" (CVT: RE0F10A) or TM-314, "CVT CONTROL SYSTEM : Component Parts Location" (RE0F11A).

10. ABS actuator and electric unit (control unit) Refer to BRC-9, "Component Parts Location" (Without ESP) or BRC-97, "Component Parts Location" (With ESP).

11. BCM Refer to BCS-6, "BODY CONTROL SYSTEM : Component Parts Location".

12. Front door lock assembly 13. Front door switch (driver side) 14. Power window main switch (door lock/unlock switch)

Component Description

BCM


BCM

BCM performs the ID verification between BCM and ECM when ignition switch is turned ON.

If the verification result is OK, ECM can start engine. If the verification result is NG, ECM cannot start engine.

IPDM E/R

Starter control relay is integrated in IPDM E/R and used for the engine starting system. Starter control relay is controlled by IPDM E/R while communicating with BCM and ECM. IPDM E/R sends the starter control relay status signal to ECM.

Door Switch

Door switch detects door open/close condition and then transmits ON/OFF signal to BCM.

Hood Switch

Hood switch detects that hood is open, and then transmits the signal to IPDM E/R. IPDM E/R transmits hood switch signal to BCM via CAN communication.

Ignition Key

The ID verification is performed between BCM and ignition key via NATS antenna amp. when ignition switch is turned ON. If an unregistered ID of ignition key is used, the operation of the starting engine is prohibited.

NATS Antenna Amp

The ID verification is performed between BCM and ignition key via NATS antenna amp. when ignition switch is turned ON. If an unregistered ID of ignition key is used, the operation of the starting engine is prohibited.

Remote Keyless Entry Receiver

Remote keyless entry receiver receives each button operation signal and electronic key ID signal from Keyfob, and then transmits the signal to BCM.

Security Indicator Lamp

Security indicator lamp is located on combination meter.

Security indicator lamp blinks when power supply position is in any position except the ON position to warn that Nissan Anti-Theft System (NATS) is on board.

Starter Control Relay

Starter control relay is integrated in IPDM E/R and used for the engine starting system. Starter control relay is controlled by IPDM E/R while communicating with BCM and ECM. IPDM E/R sends the starter control relay status signal to ECM.

Transmission Range Switch

Transmission range switch is integrated in CVT assembly to detect the selector lever position, and then transmits the P/N position signal to IPDM E/R.

    System
    NISSAN anti-theft system NISSAN ANTI-THEFT SYSTEM : System Diagram NISSAN ANTI-THEFT SYSTEM : System Description SYSTEM DESCRIPTION Nissan Anti-Theft System (NATS) has the following immobilizer ...

    Other materials:

    P0848 transmission fluid pressure SEN/SW B
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PREPARATION BEFORE WORK If another "DTC CONFIRMATION PROCEDURE" occurs just before, the ignition switch OFF and wait for at least 10 seconds, then perform the next test. >> GO TO 2. 2.CHECK DTC DETECTION With ...

    Service
    • Never use electrical test equipment to check SRS circuits unless instructed to in this Service Manual. • Before servicing the SRS, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3 minutes. For approximately 3 minutes after the battery negative terminal ar ...

    Service Notice or Precautions for EPS System
    • Check the following item when performing the trouble diagnosis. - Check any possible causes by interviewing the symptom and it′s condition from the customer if any malfunction, such as EPS warning lamp is turned ON, occurs. - Check if air pressure and size of tires are proper, the spe ...