Nissan Juke Service and Repair Manual : Brake warning lamp

Component Function Check

1.CHECK BRAKE WARNING LAMP FUNCTION (1)

Check that brake warning lamp in combination meter turns ON for approx. 1 second after ignition switch is turned ON.

CAUTION:
Never start engine.

Is the inspection result normal? YES >> GO TO 2.

NO >> Proceed to BRC-208, "Diagnosis Procedure".

2.CHECK BRAKE WARNING LAMP FUNCTION (2)

Check that brake warning lamp in combination meter turns ON/OFF when parking brake is operated.

NOTE

:
Brake warning lamp turns ON when parking brake is operated (when parking brake switch is ON).

Is the inspection result normal? YES >> GO TO 3.

NO >> Check parking brake switch system. Refer to BRC-208, "Diagnosis Procedure".

3.CHECK BRAKE WARNING LAMP FUNCTION (3)

Check that brake warning lamp in combination meter turns ON/OFF when brake fluid level switch is operated while brake fluid level in reservoir tank is with the specified level.

NOTE

:
Brake warning lamp turns ON when brake fluid is less than the specified level (when brake fluid level switch is ON).

Is the inspection result normal? YES >> INSPECTION END

NO >> Check brake fluid level switch system. Refer to BRC-208, "Diagnosis Procedure"

Diagnosis Procedure

1.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit.

Refer to BRC-205, "Diagnosis Procedure".

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace error-detected parts.

2.PERFORM THE SELF-DIAGNOSIS

Perform self-diagnosis for “ABS”.With CONSULT-III.


Perform self-diagnosis for “ABS”.

Is any DTC detected? YES >> Check the DTC. Refer to BRC-142, "DTC Index".

NO >> GO TO 3.

3.CHECK COMBINATION METER

Check combination meter. Refer to MWI-23, "CONSULT-III Function".

Is the inspection result normal? YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-233, "Removal and Installation".

NO >> Repair or replace combination meter. Refer to MWI-69, "Removal and Installation".

    ABS warning lamp
    Component Function Check 1.CHECK ABS WARNING LAMP FUNCTION Check that ABS warning lamp in combination meter turns ON for approx. 1 second after ignition switch is turned ON. CAUTION: Never st ...

    ESP warning lamp
    Component Function Check 1.CHECK ESP WARNING LAMP FUNCTION Check that ESP warning lamp in combination meter turns ON for approx. 1 second after ignition switch is turned ON. CAUTION: Never st ...

    Other materials:

    Ignition coil, spark plug and rocker cover
    Exploded View 1. Rocker cover protector 2. O-ring 3. PCV control valve 4. PCV hose 5. Clamp 6. Rocker cover gasket 7. Rocker cover 8. Clamp 9. PCV hose 10. Oil filler cap 11. Spark plug 12. Ignition coil A. To air duct assembly B.Tightening must be done following the instal ...

    P0002 fuel pump
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0002 is displayed with DTC P0087, P0089, P0090 or P0190, first perform trouble diagnosis for DTC P0087, P0089, P0090 or P0190. Refer to EC-895, "DTC Logic" (DTC P0087), EC-897, "DTC Logic" (DTC P0089), EC-899, "DTC Logic&q ...

    P0225 APP sensor
    DTC Logic DTC DETECTION LOGIC NOTE: • If DTC P0225 is displayed with DTC P0641, first perform trouble diagnosis for DTC P0641. Refer to EC-974, "DTC Logic". Diagnosis Procedure 1.CHECK GROUND CONNECTIONS 1. Turn ignition switch OFF. 2. Check ground connection E38. Refer to Grou ...