Nissan Juke Service and Repair Manual : B1050, B1055 driver air bag module

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.CHECK SELF-DIAG RESULT

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

1. Turn ignition switch ON.Without CONSULT-III


1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to SRC-12, "On Board Diagnosis Function".

NOTE

:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected? YES >> Refer to SRC-47, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more. (To discharge backup capacitor.) • Never use unspecified tester or other measuring device.

1.CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal? YES >> GO TO 2.

NO >> Replace harness connector.

2.CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal? YES >> GO TO 3.

NO >> Replace wiring harness.

3.REPLACE SPIRAL CABLE

1. Replace combination switch (spiral cable). Refer to SR-16, "Removal and Installation".

2. Perform DTC confirmation procedure. Refer to SRC-47, "DTC Logic".

Is DTC detected? YES >> GO TO 4.

NO >> INSPECTION END

4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace air bag diagnosis sensor unit. Refer to SR-30, "Removal and Installation".

2. Perform DTC confirmation procedure. Refer to SRC-47, "DTC Logic".

Is DTC detected? YES >> GO TO 5.

NO >> INSPECTION END

5.REPLACE DRIVER AIR BAG MODULE

1. Replace driver air bag module. Refer to SR-13, "Removal and Installation".

2. Perform DTC confirmation procedure. Refer to SRC-47, "DTC Logic".

Is DTC detected? YES >> GO TO 1.

NO >> INSPECTION END

    B1049, B1054 driver air bag module
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” usi ...

    B1051, B1056 driver air bag module
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” usi ...

    Other materials:

    Replacing
    Replace the wiper blades if they are worn. Before replacing the wiper blades, the wiper should be in the fully up position to avoid scratching the engine hood or damaging the wiper arm. To pull up the wiper arm, see “Windshield wiper and washer switch” . 1. Lift the wiper arm away from t ...

    Air cleaner and air duct
    Exploded View 1. Hose clamp 2. PCV hose 3. Hose clamp 4. Air cleaner filter 5. Air cleaner filter case 6. Grommet 7. Inlet air duct (lower) 8. Grommet 9. Inlet air duct (upper) 10. Bracket 11. Air cleaner case 12. O-ring 13. Mass air flow sensor 14. Air duct A. To electric ...

    P060B ECM
    DTC Logic DTC DETECTION LOGIC Diagnosis Procedure 1.INSPECTION START 1. Turn ignition switch ON. 2. Erase DTC. 3. Turn ignition switch OFF and wait for 20 seconds. 4. Turn ignition switch ON and perform the self-diagnosis. Is the DTC P060B displayed again? YES >> GO TO 2. NO &g ...