Nissan Juke Service and Repair Manual : Wheel sensor

Front wheel sensor : Exploded View

1. Front LH wheel sensor


1. Front LH wheel sensor 2. Front LH wheel sensor harness connector

: N·m (kg-m, in-lb): Vehicle front
NOTE:: N·m (kg-m, in-lb)


NOTE

:
Front RH wheel sensor is symmetrically opposite of LH.

Front wheel sensor : Removal and Installat

REMOVAL

1. Remove tires.

2. Remove the fender protector (front). Refer to EXT-22, "Removal and Installation".

3. Remove front wheel sensor from steering knuckle.

CAUTION:
Never rotate and never pull front wheel sensor as much as possible, when pulling out

.

4. Remove front wheel sensor harness from the vehicle.

CAUTION:
Never twist or pull front wheel sensor harness, when removing.

INSTALLATION

Note the following, and install in the reverse order of the removal.

• Check that there is no foreign material like iron powder or damage on inner surface of front wheel sensor mounting hole of steering knuckle and sensor rotor. Install after cleaning when there are foreign material like iron powder, or replace when there is a malfunction.

• Never twist front wheel sensor harness when installing front wheel sensor. Check that grommet (2) is fully inserted to bracket (1).

Check that front wheel sensor harness is not twisted after installation.

Rear wheel sensor : Exploded View


Rear wheel sensor : Exploded View

LEFT SIDE

1. Rear LH wheel sensor


1. Rear LH wheel sensor 2. Rear LH wheel sensor harness connector

: N·m (kg-m, in-lb): Vehicle front
RIGHT SIDE: N·m (kg-m, in-lb)


RIGHT SIDE

1. Rear RH wheel sensor


1. Rear RH wheel sensor 2. Rear RH wheel sensor harness connector

: N·m (kg-m, in-lb): Vehicle front
Rear wheel sensor : Removal and Installation: N·m (kg-m, in-lb)


Rear wheel sensor : Removal and Installation

REMOVAL

1. Remove rear wheel sensor from wheel hub and bearing assembly.

CAUTION:
Never rotate or pull rear wheel sensor as much as possible, when pulling out.

2. Remove rear wheel sensor harness from the vehicle.

CAUTION:
Never twist and never pull rear wheel sensor harness, when removing.

INSTALLATION

Note the following, and install in the reverse order of the removal.

• Check that there is no foreign material like iron powder or damage on inner surface of rear wheel sensor mounting hole of wheel hub and bearing assembly and sensor rotor. Install after cleaning when there are foreign material like iron powder, or replace when there is a malfunction.

• Never twist rear wheel sensor harness when installing rear wheel sensor. Check that grommet (2) is fully inserted to bracket (1).

Check that rear wheel sensor harness is not twisted after installation.

CAUTION:


CAUTION:
Check that the identification line (A) of the rear wheel sensor is faced upward.

Sensor rotor


    Sensor rotor
    Front sensor rotor : Removal and Installation REMOVAL Replace wheel hub as an assembly when replacing because sensor rotor cannot be disassembled. Refer to FAX-43, "Removal and Installation& ...

    Other materials:

    Headlamp (HI) circuit
    Component Function Check 1.CHECK HEADLAMP (HI) OPERATION CONSULT-III ACTIVE TEST 1. Select “EXTERNAL LAMPS” of IPDM E/R active test item. 2. With operating the test items, check that the headlamp (HI) is turned ON. Hi : Headlamp (HI) ON Off : Headlamp (HI) OFF NOTE: ON/OFF is repeated 1 seco ...

    Door lock and unlock switch
    Component Function Check 1.CHECK FUNCTION 1. Select “DOOR LOCK” of “BCM” using CONSULT-III. 2. Select “CDL LOCK SW”, “CDL UNLOCK SW” in “DATA MONITOR” mode. 3. Check that the function operates normally according to the following conditions. Is the inspection result normal? YES >> Doo ...

    Ambient sensor
    Removal and Installation REMOVAL 1. Remove bumper fascia assembly. Refer to EXT-13, "Removal and Installation". 2. Disengage fixing pawl, and then remove ambient sensor (1) from air guide RH. : Pawl 3. Disconnect ambient sensor connector (2), and then remove ambient sensor. INS ...