Nissan Juke Service and Repair Manual : Vehicle security system cannot be set
Key fob
KEY FOB : Description
Armed phase is not activated when door is locked using keyfob.
NOTE
:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE
(OPERATING CONDITIONS)”
before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using CONSULT-III.
KEY FOB : Diagnosis Procedure
1.CHECK REMOTE KEYLESS ENTRY SYSTEM
Lock/unlock door with keyfob.
Refer to DLK-366, "REMOTE KEYLESS ENTRY FUNCTION : System Description" (With super lock) or DLK- 497, "System Description" (Without super lock).
Is the inspection result normal? YES >> GO TO 2.
NO >> Check remote keyless entry system. Refer to DLK-418, "Diagnosis Procedure" (With super lock) or DLK-538, "Diagnosis Procedure" (Without super lock).
2.CHECK HOOD SWITCH
Check hood switch.
Refer to SEC-223, "Component Function Check".
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace hood switch.
3.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> GO TO 1.
Door lock and unlock switch
DOOR LOCK AND UNLOCK SWITCH : Description
Armed phase is not activated when door is locked using door lock and unlock switch.
NOTE
:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE
(OPERATING CONDITIONS)”
before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using CONSULT-III.
DOOR LOCK AND UNLOCK SWITCH : Diagnosis Procedure
1.CHECK POWER DOOR LOCK SYSTEM (DOOR LOCK FUNCTION)
Lock/unlock door with door lock and unlock switch.
Refer to DLK-363, "System Description" (With super lock) or DLK-494, "System Description" (Without super lock).
Is the inspection result normal? YES >> GO TO 2.
NO >> Check power door lock system (door lock function). Refer to DLK-415, "ALL DOOR : Diagnosis Procedure" (With super lock) or DLK-534, "ALL DOOR : Diagnosis Procedure" (Without super lock).
2.CHECK HOOD SWITCH
Check hood switch.
Refer to SEC-223, "Component Function Check".
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace hood switch.
3.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> GO TO 1.
Unlock sensor
UNLOCK SENSOR : Description
Armed phase is not activated when door is locked by door key cylinder operation using mechanical key.
NOTE
:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE
(OPERATING CONDITIONS)”
before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using CONSULT-III.
UNLOCK SENSOR : Diagnosis Procedure
1.CHECK POWER DOOR LOCK SYSTEM (DOOR LOCK FUNCTION)
Lock/unlock door using mechanical key inserted into door key cylinder.
Refer to DLK-363, "System Description" (With super lock) or DLK-494, "System Description" (Without super lock).
Is the inspection result normal? YES >> GO TO 2.
NO >> Check power door lock system (door lock function). Refer to DLK-414, "Diagnosis Procedure" (With super lock) or DLK-537, "Diagnosis Procedure" (Without super lock).
2.CHECK HOOD SWITCH
Check hood switch.
Refer to SEC-223, "Component Function Check".
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace hood switch.
3.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> GO TO 1.
Security indicator lamp does not turn on or blink
Description Security indicator lamp does not blink when ignition switch is in a position other than ON. NOTE: • Before performing the diagnosis, check “Work Flow”. Refer to SEC-187, "Work ...Vehicle security alarm does not activate
Description Alarm does not operate when alarm operating condition is satisfied. NOTE: Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDITIONS)” before s ...Other materials:
Component parts
Component Parts Location
1. BCM
Refer to BCS-6, "BODY CONTROL
SYSTEM : Component Parts Location"
(With Intelligent Key system) or
BCS-96, "BODY CONTROL SYSTEM
: Component Parts Location"
(Without Intelligent Key system).
2. Rear window defogger connector
3. Rear windo ...
Normal operating condition
INFORMATION DISPLAY
INFORMATION DISPLAY : Description
AMBIENT TEMPERATURE
The displayed ambient temperature on the information display may differ from
the actual temperature because
it is a corrected value calculated from the ambient sensor signal by the
combination meter. Refer to MWI-16,
...
B2192 ID discord, IMMU-ECM
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT-III.
Is DTC detected?
YES >> Go to SEC-60, "Diagnosis Procedure".
NO >> I ...