Nissan Juke Service and Repair Manual : Vehicle security system cannot BE set
INTELLIGENT KEY
INTELLIGENT KEY : Description
Armed phase is not activated when door is locked using Intelligent Key.
NOTE
:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE
(OPERATING CONDITIONS)”
before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using CONSULT-III.
INTELLIGENT KEY : Diagnosis Procedure
1.CHECK INTELLIGENT KEY SYSTEM (REMOTE KEYLESS ENTRY FUNCTION)
Lock/unlock door with Intelligent Key.
Refer to DLK-28, "DOOR LOCK FUNCTION : System Description" (With super lock) or DLK-205, "DOOR LOCK FUNCTION : System Description" (Without super lock).
Is the inspection result normal? YES >> GO TO 2.
NO >> Check Intelligent Key system (remote keyless entry function). Refer to DLK-113, "Diagnosis Procedure" (With super lock) or DLK-279, "Diagnosis Procedure" (Without super lock).
2.CHECK HOOD SWITCH
Check hood switch.
Refer to SEC-155, "Component Function Check".
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace hood switch.
3.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> GO TO 1.
Door request switch
DOOR REQUEST SWITCH : Description
Armed phase is not activated when door is locked using door request switch.
NOTE
:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE
(OPERATING CONDITIONS)”
before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using CONSULT-III.
DOOR REQUEST SWITCH : Diagnosis Procedure
1.CHECK INTELLIGENT KEY SYSTEM (DOOR LOCK FUNCTION)
Lock/unlock door with door request switch.
Refer to DLK-28, "DOOR LOCK FUNCTION : System Description" (With super lock) or DLK-205, "DOOR LOCK FUNCTION : System Description" (Without super lock).
Is the inspection result normal? YES >> GO TO 2.
NO >> Check Intelligent Key system (door lock function). Refer to DLK-106, "ALL DOOR REQUEST SWITCHES : Diagnosis Procedure" (With super lock) or DLK-272, "ALL DOOR REQUEST SWITCHES : Diagnosis Procedure" (Without super lock).
2.CHECK HOOD SWITCH Check hood switch.
Refer to SEC-155, "Component Function Check".
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace hood switch.
3.CONFIRM THE OPERATION Confirm the operation again.
Is the result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> GO TO 1.
Unlock sensor
UNLOCK SENSOR : Description
Armed phase is not activated when door is locked by door key cylinder operation using mechanical key.
NOTE
:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE
(OPERATING CONDITIONS)”
before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using CONSULT-III.
UNLOCK SENSOR : Diagnosis Procedure
1.CHECK DOOR LOCK FUNCTION
Lock/unlock door using meahanical key inserted into door key cylinder.
Refer to DLK-24, "System Description" (With super lock), DLK-201, "System Description" (Without super lock).
Is the inspection result normal? YES >> GO TO 2.
NO >> Check Intelligent Key system (remote keyless entry function). Refer to DLK-109, "Diagnosis Procedure" (With super lock) or DLK-275, "Diagnosis Procedure" (Without super lock).
2.CHECK HOOD SWITCH
Check hood switch.
Refer to SEC-155, "Component Function Check".
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace hood switch.
3.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> GO TO 1.
Security indicator lamp does not turn on or blink
Description Security indicator lamp does not blink when ignition switch is in a position other than ON. NOTE: • Before performing the diagnosis, check “Work Flow”. Refer to SEC-47, "Work ...Vehicle security alarm does not activate
Description Alarm does not operate when alarm operating condition is satisfied. NOTE: Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDITIONS)” before s ...Other materials:
P181D engine torque signal
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn
ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.DTC REPRODUCTION PROCEDURE
With ...
Power supply and ground circuit
Diagnosis Procedure
1.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) IGNITION POWER
SUPPLY
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connector.
3. Check voltage between ABS actuator and electric unit (control unit) harness
conne ...
Precaution
Service Notice or Precautions for Road Wheel
• Genuine NISSAN aluminum wheel is designed for each type of vehicle. Use it
on the specified vehicle only.
• Use Genuine NISSAN parts for the wheel nuts.
• Always use them after adjusting the wheel balance. For the balance weights,
use Genuine NIS ...