Nissan Juke Service and Repair Manual : Vehicle information

Identification information

Japan production models

JAPAN PRODUCTION MODELS : Model Variation

Model variation code (Prefix and suffix designations)


Model variation code (Prefix and suffix designations)

JAPAN PRODUCTION MODELS : Information About Identification or Model Code


JAPAN PRODUCTION MODELS : Information About Identification or Model Code

IDENTIFICATION NUMBER

1. Air conditioner specification label


1. Air conditioner specification label 2. Vehicle identification plate 3.Vehicle identification number (Chassis number)

VEHICLE Identification Number ARRANGEMENT

IDENTIFICATION PLATE


IDENTIFICATION PLATE

1. Type approval number (Models


1. Type approval number (Models with WVTA) Blank (Models without WVTA) 2. Vehicle identification number (Chassis number)
3. Gross vehicle weight
4. Gross combination weight Gross vehicle weight + Gross trailing capacity (Weight) 5. Gross axle weight (Front) 6. Gross axle weight (Rear) 7. Vehicle type
8. Body color code
9. Trim color code
10. Model variation code

ENGINE SERIAL NUMBER

MR Engine

: Vehicle front


AUTOMATIC TRANSAXLE NUMBER


AUTOMATIC TRANSAXLE NUMBER

CVT Unit (RE0F10B)

: Vehicle front


JAPAN PRODUCTION MODELS : Dimensions


JAPAN PRODUCTION MODELS : Dimensions

JAPAN PRODUCTION MODELS : Wheels & Tires


JAPAN PRODUCTION MODELS : Wheels & Tires

Europe production models


Europe production models

EUROPE PRODUCTION MODELS : Model Variation

Model variation code (Prefix and suffix designations)


Model variation code (Prefix and suffix designations)

EUROPE PRODUCTION MODELS : Information About Identification or Model Code


EUROPE PRODUCTION MODELS : Information About Identification or Model Code

IDENTIFICATION NUMBER

1. Air conditioner specification label


1. Air conditioner specification label 2. Vehicle identification plate 3.Vehicle identification number (Chassis number)
4. Vehicle identification number plate 5. Tire placard

VEHICLE Identification Number ARRANGEMENT

IDENTIFICATION PLATE


IDENTIFICATION PLATE

1. Type approval number (Models


1. Type approval number (Models with WVTA) Blank (Models without WVTA) 2. Vehicle identification number (Chassis number)
3. Gross vehicle weight
4. Gross combination weight Gross vehicle weight + Gross trailing capacity (Weight) 5. Gross axle weight (Front) 6. Gross axle weight (Rear) 7. Vehicle type
8. Body color code
9. Trim color code
10. Model variation code

ENGINE SERIAL NUMBER

HR and MR Engine

: Vehicle front


K9K Engine


K9K Engine

Identification is engraved on the cylinder block which carries: • A: Engine type
• B: Engine type approval letter • D: Renault code
• E: Engine suffix
• F: Engine fabrication number • G: Engine assembly plant

AUTOMATIC TRANSAXLE NUMBER


AUTOMATIC TRANSAXLE NUMBER

CVT Unit (RE0F11A)

: Vehicle front


MANUAL TRANSAXLE NUMBER


MANUAL TRANSAXLE NUMBER

5M/T

1 : Serial number (bottom side of trans axle) : Vehicle front


6M/T


6M/T

: Vehicle front


EUROPE PRODUCTION MODELS : Dimensions


EUROPE PRODUCTION MODELS : Dimensions

*1: 205/60R16 model


*1: 205/60R16 model
*2: 215/55R17 model

EUROPE PRODUCTION MODELS : Wheels & Tires

Precautions


    Tightening Torque Table (New Standard Included)
    CAUTION: • The special parts are excluded. • The bolts/nuts in these tables have a strength (discrimination) number/symbol assigned to the head or the like. As to the relation between the strengt ...

    Other materials:

    B1147 curtain air bag module RH
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III. Without CONSULT-III 1. Turn ignition switch ON. 2. Check the air bag warning lamp statu ...

    B210F shift position/clutch interlock switch
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC B210F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to PCS- 30, "DTC Logic". DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE 1. Shift selector lever to the P position. 2. Turn ign ...

    Removal and Disassembly
    • When instructed to use SST, use specified tools. Always be careful to work safely, avoid forceful or uninstructed operations. • Exercise maximum care to avoid damage to mating or sliding surfaces. • Dowel pins are used for several parts alignment. When replacing and reassembling parts with ...