Nissan Juke Service and Repair Manual : Thermostat
Exploded View
1. Thermostat housing
2. Gasket
3. Rubber ring
4. Thermostat
5. Water inlet
6. Clamp
7. Radiator hose (upper)
A. To radiator
Engine front
: N·m (kg-m, ft-lb)
: Always replace after every
disassembly.
Removal and Installation
REMOVAL
1. Drain engine coolant from radiator. Refer to CO-11, "Draining".
CAUTION:
Perform this step when engine is cold.
2. Remove intake manifold. Refer to EM-28, "Exploded View".
3. Disconnect radiator hose (lower) (RH) from water inlet. Refer to CO-17, "Exploded View".
4. Remove water inlet and thermostat.
• Engine coolant leakage from cylinder block, so have a receptacle ready below.
Thermostat housing
1. Drain engine coolant. Refer to CO-11, "Draining".
2. Remove alterator. Refer to CHG-30, "MR16DDT : Exploded View".
3. Remove water pump. Refer to CO-22, "Exploded View".
4. Disconnect water hose, and them remove thermostat housing.
INSTALLATION
Note the following, and install in the reverse order of removal.
Thermostat
• Install thermostat with making rubber ring (1) groove fit to thermostat flange (A) with the whole circumference.
• Install thermostat (2) with jiggle valve (A) facing upwards.
1 : Thermostat housing
Thermostat housing
• Install in the reverse order of removal.
Inspection
INSPECTION AFTER REMOVAL
Thermostat
• Place a thread (A) so that it is caught in the valves of thermostat
(1). Immerse fully in a container (B) filled with water. Heat while
stirring.
• The valve opening temperature is the temperature at which the valve opens and falls from the thread.
• Continue heating. Check the full open valve lift amount.
• After checking the maximum valve lift amount, lower the water temperature and check the valve closing temperature.
Standard: Refer to CO-29, "Thermostat".
• If out of the standard, replace thermostat.
INSPECTION AFTER INSTALLATION
• Check for leakage of engine coolant using the radiator cap tester adapter (commercial service tool) and the radiator cap tester (commercial service tool). Refer to CO-11, "Inspection".
• Start and warm up the engine. Check visually that there is no leakage of engine coolant.
Water pump
Exploded View 1. Gasket 2. Water pump : N·m (kg-m, ft-lb) : Always replace after every disassembly. Removal and Installation REMOVAL 1. Drain engine coolant from radiator. Refer to CO-11, ...Water outlet
Exploded View 1. Heater pipe bracket 2. Radiator cap 3. Water outlet adaptor 4. Clamp 5. Water outlet hose 6. Clamp 7. Heater hose 8. Clamp 9. Water outlet 10. Clamp 11. Heater hos ...Other materials:
Configuration (bcm)
Description
Vehicle specification needs to be written with CONSULT-III because it is not
written after replacing BCM.
Configuration has three functions as follows.
NOTE:
Manual setting item: Items which need selection by vehicle specifications
Automatic setting item: Items which are written ...
Precautions
Liquid Gasket
REMOVAL OF LIQUID GASKET SEALING
• After removing mounting nuts and bolts, separate the mating surface
using the seal cutter [SST: KV10111100 (J-37228)] (A) and
remove old liquid gasket sealing.
CAUTION:
Be careful not to damage the mating surfaces.
• Tap the seal cutter [SS ...
Towing recommended by NISSAN
Two-Wheel Drive (2WD) models
NISSAN recommends that your vehicle be towed with the driving (front) wheels
off the ground or place the vehicle on a flat bed truck as illustrated.
CAUTION
• Never tow CVT models with the front wheels on the ground or four wheels
on the ground (forward or ...