Nissan Juke Service and Repair Manual : The seat belt reminder warning continues sounding, or does not sound
Description
• Seat belt reminder warning does not sound.
• Seat belt reminder warning sounds continuously.
Diagnosis Procedure
1.CHECK SEAT BELT WARNING LAMP
1. Turn ignition switch ON.
2. Check the operation of the seat belt warning lamp in the combination meter.
Seat belt (driver side) fastened : OFF Seat belt (driver side) unfastened : ON Seat belt (passenger side) fastened* : OFF Seat belt (passenger side) unfastened* : ON
*: When getting in the passenger seat Is the inspection result normal? YES >> Replace combination meter. Refer to MWI-69, "Removal and Installation".
NO >> GO TO 2.
2.CHECK SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT (DRIVER SIDE)
Perform the check for the seat belt buckle switch (driver side) circuit. Refer to MWI-58, "Diagnosis Procedure".
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)
Perform the check for the seat belt buckle switch (driver side). Refer to MWI-59, "Component Inspection".
Is the inspection result normal? YES >> GO TO 4.
NO >> Replace seat belt buckle (driver side). Refer to SB-8, "SEAT BELT BUCKLE : Removal and Installation".
4.CHECK SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT (PASSENGER SIDE)
Perform the check for the seat belt buckle switch (passenger side) circuit. Refer to MWI-60, "Diagnosis Procedure".
Is the inspection result normal? YES >> GO TO 5.
NO >> Repair harness or connector.
5.CHECK SEAT BELT BUCKLE SWITCH (PASSENGER SIDE)
Perform the check for the seat belt buckle switch (passenger side). Refer to MWI-60, "Component Inspection (Seat Belt Buckle Switch)".
Is the inspection result normal? YES >> GO TO 6.
NO >> Replace seat belt buckle (passenger side). Refer to SB-8, "SEAT BELT BUCKLE : Removal and Installation".
6.CHECK OCCUPANT DETECTION UNIT
Perform the check for the occupant detection unit. Refer to MWI-61, "Component Inspection (Occupant Detection Unit)".
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-69, "Removal and Installation".
NO >> Replace seat cushion trim and pad. Refer to SE-21, "SEAT CUSHION : Disassembly and Assembly" (2WD) or SE-29, "SEAT CUSHION : Disassembly and Assembly" (4WD).
The light reminder warning does not sound
Description Light reminder warning chime does not sound even though headlamp is illuminated. Diagnosis Procedure 1.CHECK COMBINATION SWITCH (LIGHTING SWITCH) OPERATION Check that the headlamps o ...The key warning does not sound (without intelligent key)
Description The key warning chime does not sound, when all of the following conditions are fulfilled. • Key inserted into the key cylinder (key switch signal ON). • Ignition switch is in ACC or ...Other materials:
Rear door glass
Exploded View
1. Rear door panel
2. Sealing screen
3. Lower sash (front)
4. Rear door regulator assembly
5. Power window motor
6. Rear door glass
7. Lower sash (rear)
8. Rear door glass run
Removal and Installation
REMOVAL
1. Fully open rear door glass.
2. Remove rear door finishe ...
Back door lock
Exploded View
1. Back door lock assembly 2. TORX bolt 3. Back door striker
: Do not reuse
: N·m (kg-m, ft-lb)
: Body grease
Door lock
DOOR LOCK : Removal and Installation
REMOVAL
1. Remove the back door lower finisher. Refer to INT-35, "BACK DOOR LOWER
FINISHER : Removal and
Instal ...
P0720 output speed sensor
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Be careful of the driving speed.
1.PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition
switch OFF and wait for at
least 10 seconds, then perform the next test.
> ...