Nissan Juke Service and Repair Manual : Tail lamp circuit
Without daytime running light system
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function
1.CHECK TAIL LAMP OPERATION
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the tail lamp is turned ON.
TAIL : Tail Lamp ON
Off : Tail lamp OFF
Is the inspection result normal? YES >> Tail lamp circuit is normal.
NO >> Refer to EXL-61, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure".
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure
1.CHECK TAIL LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal? YES >> GO TO 2.
NO >> Replace bulb.
2.CHECK PARKING LAMP OPERATION
Check that the parking lamp is turned ON.
Is the inspection result normal? YES-1 (When tail lamp (RH) does not turn ON.)>>GO TO 6.
YES-2 (When tail lamp (LH) does not turn ON.)>>GO TO 3.
NO >> Check parking lamp circuit. Refer to EXL-58, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function Check".
3.CHECK TAIL LAMP (LH) FUSE
1. Turn ignition switch OFF.
2. Check that the following fuses are not fusing
Is the inspection result normal? YES >> GO TO 4.
NO >> GO TO 5.
4.CHECK TAIL LAMP (LH) OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Disconnect rear combination lamp (LH) connector.
2. Turn ignition switch ON.
3. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4. With operating the test items, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal? YES >> GO TO 6.
NO >> Replace IPDM E/R.
5.CHECK TAIL LAMP (LH) SHORT CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector and rear combination lamp (LH) connector.
3. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal? YES >> Replace fuse. (Replace IPDM E/R if fusing is found again.) NO >> Repair or replace harness. And then replace the fuse.
6.CHECK TAIL LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector and rear combination lamp connector.
3. Check continuity between IPDM E/R harness connector and rear combination lamp harness connector.
Is the inspection result normal? YES >> GO TO 7.
NO >> Repair or replace harness.
7.CHECK TAIL LAMP GROUND OPEN CIRCUIT
Check continuity between rear combination lamp harness connector and ground.
Is the inspection result normal? YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.
With daytime running light system
WITH DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
1.CHECK TAIL LAMP OPERATION
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the tail lamp is turned ON.
TAIL : Tail Lamp ON
Off : Tail lamp OFF
Is the inspection result normal? YES >> Tail lamp circuit is normal.
NO >> Refer to EXL-63, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure".
WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure
1.CHECK TAIL LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal? YES >> GO TO 2.
NO >> Replace bulb.
2.CHECK PARKING LAMP OPERATION
Check that the parking lamp is turned ON.
Is the inspection result normal? YES-1 (When tail lamp (RH) does not turn ON.)>>GO TO 4.
YES-2 (When tail lamp (LH) does not turn ON.)>>GO TO 3.
NO >> Check parking lamp circuit. Refer to EXL-59, "WITH DAYTIME RUNNING LIGHT SYSTEM : Component Function Check".
3.CHECK TAIL LAMP (LH) SHORT CIRCUIT
1. Turn ignition switch OFF.
2. Remove daytime running light relay.
3. Disconnect rear combination lamp (LH) connector.
4. Check continuity between daytime running light relay harness connector and ground.
Is the inspection result normal? YES >> GO TO 4.
NO >> Repair or replace harness.
4.CHECK TAIL LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Remove daytime running light relay.
3. Disconnect rear combination lamp connector.
4. Check continuity between daytime running light relay harness connector and rear combination lamp harness connector.
Is the inspection result normal? YES >> GO TO 5.
NO >> Repair or replace harness.
5.CHECK TAIL LAMP GROUND OPEN CIRCUIT Check continuity between rear combination lamp harness connector and ground.
Is the inspection result normal? YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.
Parking lamp circuit
Without daytime running light system
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
1.CHECK PARKING LAMP OPERATION
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R a ...
License plate lamp circuit
Without daytime running light system
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
1.CHECK TAIL LAMP (RH) OPERATION
Check that the tail lamp (RH) is turned ON.
Is the inspectio ...
Other materials:
Exploded View
1. Final drive mounting bracket
2. Washer
3. Rear final drive assembly
: Vehicle front
: N·m (kg-m, ft-lb)
: Never reuse parts
: Apply multi purpose grease
: Apply gear oil.
...
Remote keyless entry system
System Diagram
System Description
DOOR LOCK AND UNLOCK OPERATION
• When door lock and unlock button of keyfob is pressed, door lock and unlock
signal transmits from keyfob to
BCM via remote keyless entry receiver.
• When BCM receives the door lock and unlock signal, it operates door lock
...
Larger children
Children should remain in a forward-facing child restraint with a harness until
they reach the maximum height or weight limit allowed by the child restraint manufacturer.
Once a child outgrows the height or weight limit of the harness-equipped forward-facing
child restraint, NISSAN recommends t ...
