Nissan Juke Service and Repair Manual : Spiral cable

Exploded View

1. Steering column upper cover


1. Steering column upper cover 2. Steering column assembly 3. Steering column lower cover 4. Side lid LH
5. TORX bolt
6. Driver air bag module 7. TORX bolt
8. Side lid RH
9. Steering wheel
10. Spiral cable
11. Steering angle sensor 12. Combination switch
13. Steering switch

: Do not reuse: Pawl
: N·m (kg-m, in-lb): Do not reuse
: N·m (kg-m, ft-lb): N·m (kg-m, in-lb)
Removal and Installation: N·m (kg-m, ft-lb)


Removal and Installation

WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or more.

• Never use the air tools or electric tools for servicing.

REMOVAL

1. Remove driver air bag module. Refer to SR-13, "Removal and Installation".

2. Remove steering wheel. Refer to ST-9, "Removal and Installation".

3. Remove steering column upper cover and steering column lower cover. Refer to IP-13, "Removal and Installation".

4. Disconnect the spiral cable body side harness connectors (A), (B) and steering angle sensor harness connectors (C).

NOTE

:
Disconnect the spiral cable body side harness connector (B) after removing the spiral cable (A).

5. Remove the spiral cable fixing screws.


5. Remove the spiral cable fixing screws.

6. Remove the spiral cable fixing pawls with remover tool (A).

: Pawl


CAUTION:: Pawl


CAUTION:
Remove pawls slowly so that they are not damaged.

7. Remove the steering angle sensor. Refer to BRC-236, "Removal and Installation".

CAUTION:
• Never impact the spiral cable.

• Replace the spiral cable if it is dropped or sustains an impact.

• Never disassemble the spiral cable.


• Never disassemble the spiral cable.

• Never apply lubricant to the spiral cable.

• Never allow oil, grease, detergent, or water to come in contact with the spiral cable.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION

:
• The spiral cable may snap during steering operation if the cable is installed in an improper position. The neutral position is set as per the following.

• Carefully turn the spiral cable clockwise to the end position.

Then turn it counterclockwise (about 2 and a half turns) and stop turning at the mark (B) when the stopper insertion holes are in the same position.

• The service part is installed in the neutral position by the stopper and can be set without adjusting after the stopper is removed.

• Never over turn the spiral cable or go beyond the number of turns required. (This causes the cable to snap) • Adjust the spiral cable locating pin (A) to the steering wheel locating pin hole (C).

• Fix the driver air bag module harnesses to the harness fixing


• Fix the driver air bag module harnesses to the harness fixing hook (A).

• If malfunction is detected by the air bag warning lamp, after repair or


• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunctioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to SRC-12, "On Board Diagnosis Function" or SRC-16, "CONSULT-III Function".

• After the work is completed, check that no system malfunction is detected by air bag warning lamp.

    Driver air bag module
    Exploded View 1. Steering column upper cover 2. Steering column assembly 3. Steering column lower cover 4. Side lid LH 5. TORX bolt 6. Driver air bag module 7. TORX bolt 8. Side lid RH ...

    Front passenger air bag module
    Exploded View 1. Front passenger air bag module 2. Instrument panel assembly : Pawl : Do not reuse : N·m (kg-m, ft-lb) Removal and Installation WARNING: • Before servicing, turn ignition sw ...

    Other materials:

    How to set SRT code
    Description OUTLINE In order to set all SRTs, the self-diagnoses as in the “SRT ITEM” table must have been performed at least once. Each diagnosis may require actual driving for a long period of time under various conditions. SRT ITEM The table below shows required self-diagnostic items t ...

    P0501, P2159 vehicle speed sensor
    Description ECM receives a rear wheel sensor signal from ABS actuator and electric unit (control unit) via CAN communication to switch combustion for the direct injection gasoline system. For the direct injection gasoline system, refer toEC-48, "DIRECT INJECTION GASOLINE SYSTEM : System ...

    Back door request switch
    Component Function Check 1.CHECK FUNCTION 1. Select “INTELLIGENT KEY” of “BCM” using CONSULT-III. 2. Select “REQ SW-BD/TR” in “DATA MONITOR” mode. 3. Check that the function operates normally according to the following conditions. Is the inspection result normal? YES >> Back door req ...