Nissan Juke Service and Repair Manual : Shift lock system
Component Function Check
1.CHECK SHIFT LOCK OPERATION (PART 1)
1. Turn ignition switch ON.
2. Shift the selector lever to “P” position.
3. Attempt to shift the selector lever to any other than position with the brake pedal released.
Can the selector lever be shifted to any other position? YES >> Go to TM-255, "Diagnosis Procedure".
NO >> GO TO 2.
2.CHECK SHIFT LOCK OPERATION (PART 2)
Attempt to shift the selector lever to any other than position with the brake pedal depressed.
Can the selector lever be shifted to any other position? YES >> INSPECTION END
NO >> Go to TM-255, "Diagnosis Procedure".
Diagnosis Procedure
1.CHECK POWER SOURCE (PART 1)
1. Turn ignition switch OFF.
2. Disconnect stop lamp switch connector 3. Turn ignition switch ON.
4. Check the voltage between the stop lamp switch harness connector terminal and ground.
Is the inspection result normal? YES >> GO TO 2.
NO >> GO TO 9.
2.CHECK STOP LAMP SWITCH (PART 1)
Check stop lamp switch. Refer to TM-258, "Component Inspection (Stop Lamp Switch)".
Is the inspection result normal? YES >> GO TO 3.
NO >> GO TO 10.
3.CHECK CIRCUIT BETWEEN STOP LAMP SWITCH AND CVT SHIFT SELECTOR (PART 1)
1. Disconnect CVT shift selector connector 2. Check the continuity between the stop lamp switch harness connector terminal and the CVT shift selector harness connector terminal.
Is the inspection result normal? YES >> GO TO 4.
NO >> Repair or replace the malfunctioning parts.
4.CHECK CIRCUIT BETWEEN STOP LAMP SWITCH AND CVT SHIFT SELECTOR (PART 1)
Check the continuity between the stop lamp switch harness connector terminal and ground.
Is the inspection result normal? YES >> GO TO 5.
NO >> Repair or replace the malfunctioning parts.
5.CHCK GROUND CIRCUIT
Check the continuity between the CVT shift selector harness connector terminal and ground.
Is the inspection result normal? YES >> GO TO 6.
NO >> Repair or replace the malfunctioning parts.
6.CHECK PART POSITION SWITCH
1. Disconnect park position switch connector.
2. Check park position switch. Refer to TM-257, "Component Inspection (Park Position Switch)".
Is the inspection result normal? YES >> GO TO 7.
NO >> Repair or replace the malfunctioning parts.
7.CHECK SHIFT LOCK SOLENOID
1. Disconnect shift lock solenoid connector.
2. Check shift lock solenoid. Refer to TM-257, "Component Inspection (Shift Lock Solenoid)".
Is the inspection result normal? YES >> GO TO 8.
NO >> Repair or replace the malfunctioning parts.
8.CHECK CVT SHIFT SELECTOR HARNESS
Check CVT shift selector harness. Refer to TM-257, "Component Inspection (CVT Shift Selector Harness)".
Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> Repair or replace the malfunctioning parts.
9.DETECT MALFUNCTIONING ITEM
Check the following items: • Open or short circuit of the harness between ignition switch and stop lamp switch connector. Refer to PG-15, "Wiring Diagram - IGNITION POWER SUPPLY -".
• Ignition switch
• 10A fuse [No.3, fuse block (J/B)]. Refer to PG-22, "Fuse, Connector and
Terminal Arrangement".
Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> Repair or replace the malfunctioning parts.
10.CHECK INSTALLATION POSITION OF STOP LAMP SWITCH
Adjust stop lamp switch position. Refer to BR-9, "Inspection and Adjustment" (LHD) or BR-77, "Inspection and Adjustment" (RHD).
>> GO TO 11.
11.CHECK STOP LAMP SWITCH (PART 2)
Check stop lamp switch. Refer to TM-258, "Component Inspection (Stop Lamp Switch)".
Is the inspection result normal? YES >> INSPECTION END
NO >> Repair or replace the malfunctioning parts.
Component Inspection (Shift Lock Solenoid)
1.CHECK SHIFT LOCK SOLENOID
Apply voltage to terminals of shift lock solenoid connector and check that shift lock solenoid is activated.
CAUTION:
• Connect the fuse between the terminals when applying the voltage.
• Never cause shorting between terminals.
Is the inspection result normal? YES >> INSPECTION END
NO >> Replace the shift lock unit. Refer to TM-271, "Disassembly and Assembly".
Component Inspection (Park Position Switch)
1.CHECK PARK POSITION SWITCH
Check the continuity between park position switch connector terminals.
CAUTION:
• Connect the fuse between the terminals when applying the voltage.
• Never cause shorting between terminals.
Is the inspection result normal? YES >> INSPECTION END
NO >> Replace the park position switch. Refer to TM-271, "Disassembly and Assembly".
Component Inspection (CVT Shift Selector Harness)
1.CHECK CVT SHIFT SELECTOR HARNESS (PART 1)
Check the continuity between the CVT shift selector harness connector terminal and the shift lock solenoid harness connector terminal.
Is the inspection result normal? YES >> GO TO 2.
NO >> Replace the CVT shift selector harness. Refer to TM-271, "Disassembly and Assembly".
2.CHECK CVT SHIFT SELECTOR HARNESS (PART 2)
Check the continuity between the shift lock solenoid harness connector terminal and the park position switch harness connector terminal.
Is the inspection result normal? YES >> GO TO 3.
NO >> Replace the CVT shift selector harness. Refer to TM-271, "Disassembly and Assembly".
3.CHECK CVT SHIFT SELECTOR HARNESS (PART 3)
Check the continuity between the park switch harness connector terminal and the CVT shift selector harness connector terminal.
Is the inspection result normal? YES >> GO TO 4.
NO >> Replace the CVT shift selector harness. Refer to TM-271, "Disassembly and Assembly".
4.CHECK CVT SHIFT SELECTOR HARNESS (PART 4)
Check harness cladding CVT shift selector harness for damage.
Is the inspection result normal? YES >> INSPECTION END
NO >> Replace the CVT shift selector harness. Refer to TM-271, "Disassembly and Assembly".
Component Inspection (Stop Lamp Switch)
1.CHECK STOP LAMP SWITCH
Check the continuity between the stop lamp switch connector terminals.
Is the inspection result normal? YES >> INSPECTION END
NO >> Replace stop lamp switch. Refer to BR-21, "Removal and Installation" (LHD) or BR-89, "Removal and Installation" (RHD).
Shift position indicator circuit
Description
• TCM sends position indicator signals to combination meter by CAN
communication line.
• Manual mode switch position is indicated on shift position indicator
Component Function Check
...
Symptom diagnosis
SYSTEM SYMPTOM
Symptom Table
The diagnostics item numbers show the sequence for inspection. Inspect in
order from item 1.
...
Other materials:
Back door opener system
System Diagram
System Description
BACK DOOR OPENER OPERATION
When back door opener switch is pressed, BCM operates back door opener
actuator.
NOTE:
Back door opener actuator is not for locking the back door. The function is only
to open the back door.
OPERATION CONDITION
If the foll ...
Trouble diagnosis
System Diagram
Condition of Error Detection
DTC (e.g. U1000 and U1001) of CAN communication is indicated on SELF-DIAG
RESULTS on CONSULT-III
if a CAN communication signal is not transmitted or received between units for 2
seconds or more.
CAN COMMUNICATION SYSTEM ERROR
• CAN communicati ...
Rear door
Exploded View
1. Rear door panel
2. Door hinge (upper)
3. Door hinge (lower)
4. Door check link
5. Door striker
6. TORX bolt
: Do not reuse
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Body grease
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
CAUTION:
• Perform work with 2 ...
